參數資料
型號： CP2201EK
廠商： Silicon Laboratories Inc
文件頁數： 85/108頁
文件大?。?/td> 0K
描述： KIT EVAL FOR CP2201 ETH CTRLR
標準包裝： 1
主要目的： 接口，以太網傳感器
嵌入式： 是，MCU，8 位
已用 IC / 零件： CP2200，CP2201
主要屬性： 溫度和光傳感器
次要屬性： 圖形用戶界面
已供物品： 板，電源，線纜，CD
產品目錄頁面： 627 (CN2011-ZH PDF)
相關產品： 336-1313-ND - IC ETH CTRLR SNGL-CHIP 28QFN
336-1312-ND - IC ETH CTRLR SNGL-CHIP 48TQFP
其它名稱： 336-1316
CP2200/1
78
Rev. 1.0
14. Media Access Controller (MAC)
The CP2200/1 has an IEEE 802.3 compliant Ethernet Media Access Controller (MAC). The MAC can be
configured to automatically pad short frames (full duplex mode only), append CRC, and perform frame length
checking. A loopback mode separate from PHY loopback is also provided for system debugging. The MAC is
configured through nine indirect 16-bit registers summarized in Table 20.
14.1. Initializing the MAC
MAC initialization occurs after the physical layer initialization and typically occurs once after each reset or Auto-
Negotiation Complete interrupt. Most MAC indirect registers can be left at their reset values. See “6.2. Reset
Initialization” on page 18 for the complete reset initialization procedure. The following are the steps required to
initialize the MAC:
Step 1: Determine if the physical layer is set to full-duplex or half-duplex. The MAC must be set to the same
duplex mode as the physical layer before sending or receiving any packets.
Step 2: Write 0x40B3 (full-duplex) or 0x4012 (half-duplex) to MACCF. The appropriate bits in this register
may also be set or cleared to change padding options or MAC behavior.
Step 3: Write 0x0015 (full-duplex) or 0x0012 (half-duplex) to IPGT.
Step 4: Write 0x0C12 to IPGR.
Step 5: Write 0x05EE to MAXLEN.
Step 6: Program the 48-bit Ethernet MAC Address by writing to MACAD0:MACAD1:MACAD2.
Step 7: Write 0x0001 to MACCN to enable reception. If loopback mode or flow control is desired, set the
appropriate bits to enable these functions.
14.2. Accessing the Indirect MAC Registers
The indirect MAC registers are accessed through four direct mapped registers: MACADDR, MACDATAH,
MACDATAL, and MACRW. The MAC registers can be accessed using the following procedure:
Step 1: Write the address of the indirect register to MACADDR.
Step 2: If writing a value to the indirect register, write a 16-bit value to MACDATAH:MACDATAL.
Step 3: Write any value to MACRW to transfer the contents of MACDATAH:MACDATAL to the indirect
register.
Step 4: Perform a read on MACRW to transfer the contents of the indirect register to
MACDATAH:MACDATAL. The MACDATAH and MACDATAL registers may now be directly read to
determine the contents of the indirect register.
相關PDF資料
PDF描述
PM1210-820J-RC INDUCTOR 82UH 5% 1210 SMD
H3WWH-6036G IDC CABLE - HPL60H/AE60G/HPL60H
UPS2C471MRD CAP ALUM 470UF 160V 20% RADIAL
A3CKB-4006M IDC CABLE - AKC40B/AE40M/APK40B
MODEMDK KIT DEV EMBEDDED MODEM
相關代理商/技術參數
參數描述
CP2201-GM 功能描述:以太網 IC Ethernet Controller RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
CP2201-GMR 功能描述:以太網 IC Ethernet Controller RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
CP-220-K 制造商:PREMO 制造商全稱:PREMO CORPORATION S.L 功能描述:Coils and Chokes for general use
CP221 制造商:CENTRAL 制造商全稱:Central Semiconductor Corp 功能描述:Small Signal Transistor
CP-221 1 1/2"BL 100' 功能描述:HEATSHRNK CP221 1-1/2" X 100'BLK 制造商:3m 系列:CP-221 零件狀態:過期 類型:套管，彈性 收縮率:2 至 1 長度:100'（30.48m） 內徑（出廠）:1.500"（38.1mm） 內徑 - 恢復后:0.752"（19.1mm） 恢復后的壁厚:0.040"（1.02mm） 材料:聚烯烴（PO） 特性:自熄滅 顏色:黑 工作溫度:-55°C ~ 135°C 收縮溫度:121°C 標準包裝:1
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*