參數資料
型號： CP2201EK
廠商： Silicon Laboratories Inc
文件頁數： 40/108頁
文件大?。?/td> 0K
描述： KIT EVAL FOR CP2201 ETH CTRLR
標準包裝： 1
主要目的： 接口，以太網傳感器
嵌入式： 是，MCU，8 位
已用 IC / 零件： CP2200，CP2201
主要屬性： 溫度和光傳感器
次要屬性： 圖形用戶界面
已供物品： 板，電源，線纜，CD
產品目錄頁面： 627 (CN2011-ZH PDF)
相關產品： 336-1313-ND - IC ETH CTRLR SNGL-CHIP 28QFN
336-1312-ND - IC ETH CTRLR SNGL-CHIP 48TQFP
其它名稱： 336-1316
CP2200/1
Rev. 1.0
37
9. Reset Sources
Reset circuitry allows the CP2200/1 to be easily placed in a predefined default condition. Upon entry to this reset
state, the following events occur:
All direct and indirect registers are initialized to their defined reset values.
Digital pins (except /RST) are forced into a high impedance state with a weak pull-up to VDD.
Analog pins (TX+/TX–, RX+/RX–) are forced into a high impedance state without a weak pull-up.
The external oscillator is stopped and /RST driven low (except on a software reset).
All interrupts are enabled.
The contents of the transmit and receive buffers are unaffected by a reset as long as the device has maintained
sufficient supply voltage. However, since the buffer pointers are reset to their default values, the data is effectively
lost unless the host processor has kept track of the starting address and length of each packet in the buffer.
The CP2200/1 has five reset sources that place the device in the reset state. The method of entry to the reset state
determines the amount of time spent in reset and the behavior of the /RST pin. Each of the following reset sources
is described in the following sections:
Power-On
Power-Fail
Oscillator-Fail
External /RST Pin
Software Command
Upon exit from the reset state, the device automatically starts the external oscillator and waits for it to settle (this
step is skipped on software reset). Once the crystal oscillator settles, the Oscillator Initialization Complete interrupt
occurs (interrupt pin asserted), and the host processor may now access the internal registers to poll for the Self
Initialization Complete Interrupt. If the host does not have access to the interrupt signal, it should wait
approximately 1 ms after the rising edge of reset pin prior to polling the internal registers. Note that the reset pin
could remain low up to 100 ms depending on the power supply ramp time.
The device is fully functional after the Self Initialization has completed. See “6.2. Reset Initialization” on page 18 for
the recommended initialization procedure following a device reset.
相關PDF資料
PDF描述
PM1210-820J-RC INDUCTOR 82UH 5% 1210 SMD
H3WWH-6036G IDC CABLE - HPL60H/AE60G/HPL60H
UPS2C471MRD CAP ALUM 470UF 160V 20% RADIAL
A3CKB-4006M IDC CABLE - AKC40B/AE40M/APK40B
MODEMDK KIT DEV EMBEDDED MODEM
相關代理商/技術參數
參數描述
CP2201-GM 功能描述:以太網 IC Ethernet Controller RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
CP2201-GMR 功能描述:以太網 IC Ethernet Controller RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
CP-220-K 制造商:PREMO 制造商全稱:PREMO CORPORATION S.L 功能描述:Coils and Chokes for general use
CP221 制造商:CENTRAL 制造商全稱:Central Semiconductor Corp 功能描述:Small Signal Transistor
CP-221 1 1/2"BL 100' 功能描述:HEATSHRNK CP221 1-1/2" X 100'BLK 制造商:3m 系列:CP-221 零件狀態:過期 類型:套管，彈性 收縮率:2 至 1 長度:100'（30.48m） 內徑（出廠）:1.500"（38.1mm） 內徑 - 恢復后:0.752"（19.1mm） 恢復后的壁厚:0.040"（1.02mm） 材料:聚烯烴（PO） 特性:自熄滅 顏色:黑 工作溫度:-55°C ~ 135°C 收縮溫度:121°C 標準包裝:1
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*