參數資料
型號： CDB4382A
廠商： Cirrus Logic, Inc.
英文描述： 114 dB, 192 kHz 8-channel D/A Converter
中文描述： 114分貝192千赫8通道D / A轉換
文件頁數： 27/47頁
文件大?。?/td> 685K
代理商： CDB4382A
DS618PP1
27
CS4382A
3.12
Recommended Power-Up Sequence
3.12.1
Hardware Mode
1.
Hold RST low until the power supplies and configuration pins are stable, and the master and left/right
clocks are locked to the appropriate frequencies, as discussed in section 3.1. In this state, the registers
are reset to the default settings, FILT+ will remain low, and VQ will be connected to VA/2.
If RST can not be held low long enough the SDINx pins should remain static low until all other clocks
are stable, and if possible the RST should be toggled low again once the system is stable.
2.
Bring RST high. The device will remain in a low power state with FILT+ low and will initiate the
Hardware power-up sequence after approximately 512 LRCK cycles in Single-Speed Mode (1024
LRCK cycles in Double-Speed Mode, and 2048 LRCK cycles in Quad-Speed Mode).
3.12.2
Software Mode
1.
Hold RST low until the power supply is stable, and the master and left/right clocks are locked to the
appropriate frequencies, as discussed in section 3.1. In this state, the registers are reset to the default
settings, FILT+ will remain low, and VQ will be connected to VA/2.
2.
Bring RST high. The device will remain in a low power state with FILT+ low for 512 LRCK cycles in
Single-Speed Mode (1024 LRCK cycles in Double-Speed Mode, and 2048 LRCK cycles in Quad-
Speed Mode).
3.
In order to reduce the chances of clicks and pops, perform a write to the CP_EN bit prior to the
completion of approximately 512 LRCK cycles in Single-Speed Mode (1024 LRCK cycles in Double-
Speed Mode, and 2048 LRCK cycles in Quad-Speed Mode). The desired register settings can be
loaded while keeping the PDN bit set to 1. Set the RMP_UP and RMP_DN bits to 1, then set the format
and mode control bits to the desired settings.
If more than the stated number of LRCK cycles passes before CPEN bit is written then the chip will
enter Hardware mode and begin to operate with the M0-M3 as the mode settings. CPEN bit may be
written at anytime, even after the Hardware sequence has begun. It is advised that if the CPEN bit can
not be set in time then the SDINx pins should remain static low (this way no audio data can be
converted incorrectly by the hardware mode settings).
4.
Set the PDN bit to 0. This will initiate the power-up sequence, which lasts approximately 50 μs.
3.13
Recommended Procedure for Switching Operational Modes
For systems where the absolute minimum in clicks and pops is required, it is recommended that the MUTE
bits are set prior to changing significant DAC functions (such as changing sample rates or clock sources).
The mute bits may then be released after clocks have settled and the proper modes have been set.
It is required to have the device held in reset if the minimum high/low time specs of MCLK can not be met
during clock source changes.
相關PDF資料
PDF描述
CDB4382 114 dB, 192 kHz 8-Channel D/A Converter
CDB4383 RES 1K-OHM 1% 0.10W 50PPM MET-FILM AXIAL BULK MIL-R-10509
CDB4384 103 dB, 192 kHz 8-Channel D/A Converter
CDB4385 114 dB, 192kHz 8-CHANNEL D/A CONVERTER
CDB4390 RESISTOR-1K, 1/10W, 1% MFILM, RN55C
相關代理商/技術參數
參數描述
CDB4383 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:114 dB, 192 kHz 8-Channel D/A Converter
CDB4384 功能描述:音頻 IC 開發工具 Eval Bd 8-Ch DAC w/DSD RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
CDB4385 功能描述:音頻 IC 開發工具 Eval Bd 8-Ch DAC w/DSD RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
CDB4390 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:24-Bit, Stereo D/A Converter for Digital Audio
CDB4391 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:24-Bit, 192 kHz Stereo DAC with Volume Control
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*