
Mobile Intel Celeron Processor (0.18) in BGA2 and Micro-PGA2 Packages
at 700MHz, 650 MHz, 600 MHz, 550 MHz, 500 MHz, 450 MHz,
Low-voltage 500 MHz, and Low-voltage 400A MHz
Datasheet
Order#-XXX
15
3.5
DC Specifications
Table 9 through
Table 12 lists the DC specifications for the mobile Celeron processor.
Specifications are valid only while meeting specifications for junction temperature, clock
frequency, and input voltages. Care should be taken to read all notes associated with each
parameter.
Table 9. Mobile Celeron Processor Power Specifications
1
TJ = 0°C to 100°C; VCC = 1.35V ±100 mV or 1.60V ±115 mV; VCCT = 1.50V ±115 mV Symbol Parameter
Min
Typ
Max
Unit Notes
VCC
Transient VCC for core logic
1.25
1.485
1.35
1.60
1.45
1.715
V
±100 mV
±115 mV,
Note 7, 8
VCC,DC
Static VCC for core logic
1.25
1.485
1.35
1.60
1.45
1.640
V
±100 mV
-115/+40 mV,
Note 2, 8
VCCT
VCC for System Bus Buffers, Transient tolerance
1.385 1.50
1.615
V
±115 mV,
Note 7,8
VCCT,DC
VCC for System Bus Buffers, Static tolerance
1.455 1.50
1.545
V
±3%,
Note 2, 8
ICC
Current for VCC at core frequency
at 400A MHz & 1.35V
at 500 MHz & 1.35V
at 450 MHz & 1.60V
at 500 MHz & 1.60V
at 550 MHz & 1.60V
at 600 MHz & 1.60V
at 650 MHz & 1.60V
at 700 MHz & 1.60V
7.8
9.5
9.6
10.6
11.6
12.6
13.6
14.6
A
Note 4
ICCT
Current for VCCT
2.5
A
Notes 3, 4
ICC,SG
Processor Stop Grant and Auto Halt current
at 1.35V (for 400A MHz, 500 MHz)
at 1.60V (for 450 MHz, 500 MHz, 550 MHz, 600 MHz, 650 MHz)
at 1.60V (for 700 MHz)
1.7
2.2
3.5
A
Note 4
ICC,QS
Processor Quick Start and Sleep current
at 1.35V (for 400A MHz, 500 MHz)
at 1.60V (for 450 MHz, 500 MHz, 550 MHz, 600 MHz, 650 MHz)
at 1.60V (for 700 MHz)
1.5
1.9
3.0
A
Note 4
ICC,DSLP
Processor Deep Sleep Leakage current
at 1.35V (for 400A MHz, 500 MHz)
at 1.60V (for 450 MHz, 500 MHz, 550 MHz, 600 MHz, 650 MHz)
at 1.60V (for 700 MHz)
1.2
1.6
2.5
A
Note 4
dICC/dt
VCC power supply current slew rate
1400
A/
s Notes 5, 6
NOTES:
1.
Unless otherwise noted, all specifications in this table apply to all processor frequencies.
2.
Static voltage regulation includes: DC output initial voltage set point adjust, output ripple and noise, output load ranges specified in
Table 9above, temperature, and warm up.
3.
ICCT is the current supply for the system bus buffers, including the on-die termination.
4.
ICCx,max specifications are specified at VCC,DC max, VCCT,max, and 100°C and under maximum signal loading conditions. 5.
Based on simulations and averaged over the duration of any change in current. Use to compute the maximum inductance and reaction time of
the voltage regulator. This parameter is not tested.
6.
Maximum values specified by design/characterization at nominal VCC and VCCT.
7.
VCCx must be within this range under all operating conditions, including maximum current transients. VCCx must return to within the static
voltage specification, VCCx,DC, within 100 s after a transient event. The average of VCCx over time must not exceed 1.65V, as an arbitrarily
large time span may be used for this average.
8.
Voltages are measured at the processor package pin for the Micro-PGA2 part and at the package ball on the BGA2 part.