- 您現在的位置：買賣IC網 > PDF目錄375321 > AN701 (Vishay Intertechnology,Inc.) Designing High-Frequency DC-to-DC Converters With the Si9114A Switchmode Controller PDF資料下載
參數資料
| 型號： | AN701 |
| 廠商： | Vishay Intertechnology,Inc. |
| 英文描述： | Designing High-Frequency DC-to-DC Converters With the Si9114A Switchmode Controller |
| 中文描述： | 設計高頻型DC - DC轉換器隨著Si9114A開關模式控制器 |
| 文件頁數： | 11/20頁 |
| 文件大?。?/td> | 1113K |
| 代理商： | AN701 |
AN701
Vishay Siliconix
Document Number: 70575
16-Jan-01
www.vishay.com
11
The average input current will be determined by:
I
DC
P
in
V
in
17.65
48
0.358 A
I
A
P
in
V
in
x
17.65
48 x 0.376
0.98 A
From this equation the RMS value can also be calculated to be
approximately 0.475 A.
The Marcon TCCR70E2A335 3.3- F, 100-Vdc capacitor has an
ESR rating of 20 m
at 500 kHz. This type will therefore dissipate
P = 0.475
2
x 0.020 = 4.5 mW due to the switching current. The
ripple produced across this device will be governed by the
discharging current of the capacitor less the input dc voltage
in accordance with:
V
ripple
I
C
x t
C
where t
t
sw
x
and I
C
I
A
–
I
DC
V
ripple
0.612 A x 2 s x 0.376
3.3 F
0.14 V
Q = i x t = C x V
140 mV of ripple is probably acceptable as a first stage of
filtering. If lower ripple is required at the input, then a two stage
filter will yield better results.
Output capacitor:
C
out
I
out
8f V
out
where I
out
0.1 x I
out
C
out
0.3 A
8 x 500 kHz x 50 mV
1.5 F
V
out
= maximum output ripple voltage
= operating frequency
f
The required ESR for obtaining 50 mV of ripple would be
defined by:
ESR
max
V
out
I
out
ESR
max
50 mV
0.3 A
167 m
In practice, it is impossible to precisely match the value of a
capacitor with the required ESR, and the values of the
capacitors must often be selected to cover all operating
conditions including voltage and temperature.
The above equations and calculations are meant to help the
designer select the approximate size of the components
required, with the final selection based on practical values that
meet the minimum required. In designs operating below
500 kHz, the choice of the capacitor is dictated by the ESR,
and the best high-frequency electrolytics often require
large-size and micro-farad values to meet these
requirements. When operating at 500 kHz, the choice
becomes more based on the practical value closest to the size
and voltage rating required. For example, with electrolytics, in
order to guarantee the ESR over temperature or age, it might
have been necessary to use a radial 1000- F, 6.3-V Aluminum
Electrolytic in a 10x16 mm case (1257 mm2) to get an ESR
value below 100 m . It would also be necessary to check the
ESR with frequency at 500 kHz, as this data is seldom offered
for electrolytics. By comparison, the Marcon TCCR70E1E106
10- F, 25-Vdc is available in 7.5 x 6.3 x 2.75 (130 mm2) and
has an ESR of less than 15 m at 500 kHz. This will be ideal
for low output ripple an noise. Recently introduced organic
semiconductor electrolytics offer substantial improvements
and could also be considered. In this example, it was decided
to use 2 x 10- F capacitors in order to obtain low output ripple.
The output inductor limits the rate at which the current flows
into the output capacitor when the voltage is applied from the
primary through the transformer (Figure 21).
Figure 21
C
out
E
out
iL
L
out
E
in
From simple circuit theory, the voltage applied across an
inductor is:
V
L
Ldi
dt
where
V
L
E
in
–
E
out
and di
I
L
then L
E
in
–
E
out
x t
I
L
In forward converters, at maximum duty cycle,
Ein = 2xEout, and:
t
off
1
2 x F
SW
In this case, substituting gives:
t
off
1 S and L
E
out
x t
off
I
L
Therefore
L
5 V x 1 S
0.3 A
16.7 H
In practice, an inductor between 5 and 10 H would be an
acceptable choice, allowing for manufacturing tolerances and
variations.
The core selected is the EF12.6, which is identical to the core
selected for the transformer design. The EF12.6 is a cheap,
low-profile design available from many suppliers in all parts of
the world. A surface-mounted version of this bobbin was
selected for a design that could be entirely machine wound and
terminated. This implies that larger wire sizes are not possible,
due to automated winding restrictions.
相關PDF資料 |
PDF描述 |
|---|---|
| AN7060 | HIGH VOLTAGE INPUT AMPLIFIER CIRCUIT FOR HI FI POWER AMPLIFIER |
| AN7090 | Peripheral analog IC for audio signal processing |
| AN7090FHQ | LJT 5C 5#20 PIN REAR WALL MTG |
| AN709 | LJT 4C 4#20 SKT RECP |
| AN7161NFP | BTL High Audio Power Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AN7016NK | 制造商:Panasonic Industrial Company 功能描述:IC |
| AN7017 | 制造商:PANASONIC 制造商全稱:Panasonic Semiconductor 功能描述:FM/TV Front-end ICs for 1.5V Headphone Stereo, Radio Cassette Recorder |
| AN7017S | 制造商:PANASONIC 制造商全稱:Panasonic Semiconductor 功能描述:FM/TV Front-end ICs for 1.5V Headphone Stereo, Radio Cassette Recorder |
| AN7017SB | 制造商:PANASONIC 制造商全稱:Panasonic Semiconductor 功能描述:FM/TV Front-end ICs for 1.5V Headphone Stereo, Radio Cassette Recorder |
| AN7024 | 制造商:Panasonic Industrial Company 功能描述:IC |
發布緊急采購，3分鐘左右您將得到回復。