參數資料
型號: ADUC845BSZ8-5-RL
廠商: Analog Devices Inc
文件頁數: 72/108頁
文件大小: 0K
描述: IC FLASH MCU W/24BIT ADC 56-CSP
標準包裝: 1
系列: MicroConverter® ADuC8xx
核心處理器: 8052
芯體尺寸: 8-位
速度: 12.58MHz
連通性: I²C,SPI,UART/USART
外圍設備: POR,PSM,PWM,溫度傳感器,WDT
輸入/輸出數: 34
程序存儲器容量: 8KB(8K x 8)
程序存儲器類型: 閃存
EEPROM 大?。?/td> 4K x 8
RAM 容量: 2.25K x 8
電壓 - 電源 (Vcc/Vdd): 4.75 V ~ 5.25 V
數據轉換器: A/D 10x24b; D/A 1x12b,2x16b
振蕩器型: 內部
工作溫度: -40°C ~ 125°C
封裝/外殼: 52-QFP
包裝: 標準包裝
其它名稱: ADUC845BSZ8-5-RLDKR
ADuC845/ADuC847/ADuC848
Data Sheet
Rev. C | Page 66 of 108
USING THE SPI INTERFACE
Depending on the configuration of the bits in the SPICON
SFR shown in Table 41, the SPI interface transmits or receives
data in a number of possible modes. Figure 46 shows all
possible ADuC845/ADuC847/ADuC848 SPI configurations
and the timing relationships and synchronization among the
signals involved. Also shown in this figure is the SPI interrupt
bit (ISPI) and how it is triggered at the end of each byte-wide
communication.
SCLOCK
(CPOL = 1)
SCLOCK
(CPOL = 0)
(CPHA = 1)
(CPHA = 0)
SAMPLE INPUT
ISPI FLAG
DATA OUTPUT
ISPI FLAG
SAMPLE INPUT
DATA OUTPUT
?
MSB BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 LSB
SS
04741-046
Figure 46. SPI Timing, All Modes
SPI Interface—Master Mode
In master mode, the SCLOCK pin is always an output and
generates a burst of eight clocks whenever user code writes to
the SPIDAT register. The SCLOCK bit rate is determined by
SPR0 and SPR1 in SPICON. Also note that the SS pin is not
used in master mode. If the parts need to assert the SS pin on an
external slave device, a port digital output pin should be used.
In master mode, a byte transmission or reception is initiated by
a byte write to SPIDAT. The hardware automatically generates
eight clock periods via the SCLOCK pin, and the data is
transmitted via MOSI. With each SCLOCK period, a data bit is
also sampled via MISO. After eight clocks, the transmitted byte
is completely transmitted (via MOSI), and the input byte (if
required) is waiting in the input shift register (after being
received via MISO). The ISPI flag is set automatically, and an
interrupt occurs if enabled. The value in the input shift register
is latched into SPIDAT.
SPI Interface—Slave Mode
In slave mode, the SCLOCK is an input. The SS pin must also
be driven low externally during the byte communication. Trans-
mission is also initiated by a write to SPIDAT. In slave mode, a
data bit is transmitted via MISO, and a data bit is received via
MOSI through each input SCLOCK period. After eight clocks,
the transmitted byte is completely transmitted, and the input
byte is waiting in the input shift register. The ISPI flag is set
automatically, and an interrupt occurs, if enabled. The value in
the shift register is latched into SPIDAT only when the trans-
mission/reception of a byte has been completed. The end of
transmission occurs after the eighth clock has been received if
CPHA = 1, or when SS returns high if CPHA = 0.
相關PDF資料
PDF描述
MC74HCT4051ADG ANALOG MULTIPLEXERS/DEMU SOIC16
ADUC7036DCPZ IC MCU 96K FLASH DUAL 48LFCSP
MC74HC4051ADTR2G IC MUX/DEMUX 8X1 16TSSOP
ADUC7036BCPZ IC MCU FLASH 96K ANLGI/O 48LFCSP
ATSAM3X4EA-AU IC MCU 2X128KB CORTEX-M3 144-QFP
相關代理商/技術參數
參數描述
ADUC846 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter, Dual 16-Bit ADCs with Embedded 62kB FLASH MCU
ADUC846BCP32-3 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter, Dual 16-Bit ADCs with Embedded 62kB FLASH MCU
ADUC846BCP32-5 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter, Dual 16-Bit ADCs with Embedded 62kB FLASH MCU
ADUC846BCP62-3 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter, Dual 16-Bit ADCs with Embedded 62kB FLASH MCU
ADUC846BCP62-5 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter, Dual 16-Bit ADCs with Embedded 62kB FLASH MCU