- 您現在的位置：買賣IC網 > PDF目錄11199 > ADUC845BSZ8-5-RL (Analog Devices Inc)IC FLASH MCU W/24BIT ADC 56-CSP PDF資料下載
參數資料
| 型號： | ADUC845BSZ8-5-RL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 101/108頁 |
| 文件大小： | 0K |
| 描述： | IC FLASH MCU W/24BIT ADC 56-CSP |
| 標準包裝： | 1 |
| 系列： | MicroConverter® ADuC8xx |
| 核心處理器： | 8052 |
| 芯體尺寸： | 8-位 |
| 速度： | 12.58MHz |
| 連通性： | I²C，SPI，UART/USART |
| 外圍設備： | POR，PSM，PWM，溫度傳感器，WDT |
| 輸入/輸出數： | 34 |
| 程序存儲器容量： | 8KB（8K x 8） |
| 程序存儲器類型： | 閃存 |
| EEPROM 大?。?/td> | 4K x 8 |
| RAM 容量： | 2.25K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 4.75 V ~ 5.25 V |
| 數據轉換器： | A/D 10x24b; D/A 1x12b，2x16b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 125°C |
| 封裝/外殼： | 52-QFP |
| 包裝： | 標準包裝 |
| 其它名稱： | ADUC845BSZ8-5-RLDKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁當前第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁
ADuC845/ADuC847/ADuC848
Data Sheet
Rev. C | Page 92 of 108
The serial port debugger is fully contained on the device, unlike
ROM monitor type debuggers, and, therefore, no external
memory is needed to enable in-system debug sessions.
Single-Pin Emulation Mode
Built into the ADuC845/ADuC847/ADuC848 is a dedicated
controller for single-pin in-circuit emulation (ICE). In this mode,
emulation access is gained by connection to a single pin, the EA
pin. Normally on the 8051 standard, this pin is hardwired either
high or low to select execution from internal or external program
memory space. Note that external program memory or execu-
tion from external program memory is not allowed on the
devices. To enable single-pin emulation mode, users need to
pull the EA pin high through a 1 k resistor as shown in
Figure 70. The emulator then connects to the 2-pin header also
shown in Figure 70. To be compatible with the standard connec-
tor that comes with the single-pin emulator available from
Accutron Limited (www.accutron.com), use a 2-pin 0.1-inch
pitch Friction Lock header from Molex (www.molex.com) such
as part number 22-27-2021. Be sure to observe the polarity of
this header. As shown in Figure 70, when the Friction Lock tab
is at the right, the ground pin should be the lower of the two
pins when viewed from the top.
Typical System Configuration
A typical ADuC845/ADuC847/ADuC848 configuration is
shown in Figure 70. Figure 70 also includes connections for a
typical analog measurement application of the parts, namely an
interface to a resistive temperature device (RTD). The
arrangement shown is commonly referred to as a 4-wire RTD
configuration.
Here, the on-chip excitation current sources are enabled to
excite the sensor. The excitation current flows directly through
the RTD generating a voltage across the RTD proportional to its
resistance. This differential voltage is routed directly to one set
of the positive and negative inputs of the ADC (AIN1, AIN2,
respectively in this case). The same current that excited the
RTD also flows through a series resistance, RREF, generating a
ratiometric voltage reference, VREF. The ratiometric voltage
reference ensures that variations in the excitation current do not
affect the measurement system since the input voltage from the
RTD and reference voltage across RREF vary ratiometrically with
the excitation current. Resistor RREF must, however, have a low
temperature coefficient to avoid errors in the reference voltage
overtemperature. RREF must also be large enough to generate at
least a 1 V voltage reference.
The preceding example shows just a single differential ADC
connection using a single reference input pair. The ADuC845/
ADuC847/ADuC848 have the capability of connecting to five
differential inputs directly or ten single-ended inputs (LFCSP
package only) as well as having a second reference input. This
arrangement means that different sensors with different
reference ranges can be connected to the part with the need for
external multiplexing circuitry. This arrangement is shown in
Figure 71. The bridge sensor shown can be a load cell or a
pressure sensor. The RTD is shown using a reference voltage
derived from the RREF resistor via the REFIN± inputs, and the
bridge sensor is shown using a divided down AVDD reference via
the REFIN2± inputs.
相關PDF資料 |
PDF描述 |
|---|---|
| MC74HCT4051ADG | ANALOG MULTIPLEXERS/DEMU SOIC16 |
| ADUC7036DCPZ | IC MCU 96K FLASH DUAL 48LFCSP |
| MC74HC4051ADTR2G | IC MUX/DEMUX 8X1 16TSSOP |
| ADUC7036BCPZ | IC MCU FLASH 96K ANLGI/O 48LFCSP |
| ATSAM3X4EA-AU | IC MCU 2X128KB CORTEX-M3 144-QFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADUC846 | 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter, Dual 16-Bit ADCs with Embedded 62kB FLASH MCU |
| ADUC846BCP32-3 | 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter, Dual 16-Bit ADCs with Embedded 62kB FLASH MCU |
| ADUC846BCP32-5 | 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter, Dual 16-Bit ADCs with Embedded 62kB FLASH MCU |
| ADUC846BCP62-3 | 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter, Dual 16-Bit ADCs with Embedded 62kB FLASH MCU |
| ADUC846BCP62-5 | 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter, Dual 16-Bit ADCs with Embedded 62kB FLASH MCU |
發布緊急采購，3分鐘左右您將得到回復。