- 您現在的位置：買賣IC網 > PDF目錄11206 > ADUC7060BSTZ32-RL (Analog Devices Inc)IC ARM7 MCU FLASH 32K 48LQFP PDF資料下載
參數資料
| 型號： | ADUC7060BSTZ32-RL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 53/108頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ARM7 MCU FLASH 32K 48LQFP |
| 產品變化通告： | ADuC7060/1 Idd Specification Change 01/Feb/2010 |
| 設計資源： | 4 mA-to-20 mA Loop-Powered Temperature Monitor Using ADuC7060/1 (CN0145) Low power, Long Range, ISM Wireless Measuring Node (CN0164) |
| 標準包裝： | 2,000 |
| 系列： | MicroConverter® ADuC7xxx |
| 核心處理器： | ARM7 |
| 芯體尺寸： | 16/32-位 |
| 速度： | 10MHz |
| 連通性： | I²C，SPI，UART/USART |
| 外圍設備： | POR，PWM，溫度傳感器，WDT |
| 輸入/輸出數： | 14 |
| 程序存儲器容量： | 32KB（16K x 16） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 1K x 32 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.375 V ~ 2.625 V |
| 數據轉換器： | A/D 5x24b，8x24b，D/A 1x14b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 125°C |
| 封裝/外殼： | 48-LQFP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁當前第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁
Data Sheet
ADuC7060/ADuC7061
Rev. D | Page 49 of 108
ADC Configuration Register
Name:
ADCCFG
Address:
0xFFFF0518
Default value:
0x00
Access:
Read and write
Function:
The 8-bit ADC configuration MMR controls extended functionality related to the on-chip ADCs.
Table 48. ADCCFG MMR Bit Designations
Bit
Name
Description
7
GNDSW_EN
Analog ground switch enable.
This bit is set to 1 by user software to connect the external GND_SW pin to an internal analog ground
reference point. This bit can be used to connect and disconnect external circuits and components to ground
under program control and thereby minimize dc current consumption when the external circuit or
component is not being used. This bit is used in conjunction with ADCCFG[1] to select a 20 k resistor to
ground.
When this bit is cleared, the analog ground switch is disconnected from the external pin.
6:5
ADC0ACCEN[1:0]
Primary channel (32-bit) accumulator enable.
[00] = accumulator disabled and reset to 0. The accumulator must be disabled for a full ADC conversion
(ADCSTA[0] set twice) before the accumulator can be re-enabled to ensure that the accumulator is reset.
[01] = accumulator active. Positive current values are added to the accumulator total; the accumulator can
overflow if allowed to run for >65,535 conversions. Negative current values are subtracted from the
accumulator total; the accumulator is clamped to a minimum value of 0.
[10] = accumulator active. Same as [01] except that there is no clamp. Positive current values are added to the
accumulator total; the accumulator can overflow if allowed to run for >65,535 conversions. The absolute
values of negative current are subtracted from the accumulator total; the accumulator in this mode continues
to accumulate negatively, below 0.
[11] = accumulator and comparator active. This causes an ADC0 interrupt if ADCMSKI[6] is set.
4:3
ADC0CMPEN[1:0]
Primary ADC comparator enable bits.
[00] = comparator disabled.
[01] = comparator active. Interrupt asserted if absolute value of ADC0 conversion result |I| ≥ ADC0TH.
[10] = comparator count mode active. Interrupt asserted if absolute value of ADC0 conversion result |I| ≥
ADC0TH for the number of ADC0THC conversions. A conversion value |I| < ADC0TH resets the threshold
counter value (ADC0THV) to 0.
[11] = comparator count mode active, interrupt asserted if absolute value of ADC0 conversion result |I| ≥
ADC0TH for the number of ADC0THC conversions. A conversion value |I| < ADC0TH decrements the threshold
counter value (ADC0THV) toward 0.
2
ADC0OREN
ADC0 overrange enable.
Set by the user to enable a coarse comparator on the primary channel ADC. If the reading is grossly (>30%
approximate) overrange for the active gain setting, the overrange bit in the ADCSTA MMR is set. The ADC
reading must be outside this range for greater than 125 s for the flag to be set.
Do not use this feature in ADC low power mode.
1
GNDSW_RES_EN
Set to 1 to enable a 20 k resistor in series with the ground switch.
Clear this bit to disable this resistor.
0
ADCRCEN
ADC result counter enable.
Set by user to enable the result count mode. ADC interrupts occur if ADC0RCR = ADC0RCV.
Cleared to disable the result counter. ADC interrupts occur after every conversion.
相關PDF資料 |
PDF描述 |
|---|---|
| ADV3202ASWZ | IC CROSSPOINT SWIT 32X16 176LQFP |
| AD7506SQ | IC MULTIPLEXER 16X1 28CDIP |
| VI-B3T-IW-F2 | CONVERTER MOD DC/DC 6.5V 100W |
| VI-B3V-IX-F4 | CONVERTER MOD DC/DC 5.8V 75W |
| VI-B3V-IX-F3 | CONVERTER MOD DC/DC 5.8V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADUC7061BCPZ32 | 功能描述:IC MCU 16/32BIT 32KB 32LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND |
| ADUC7061BCPZ32-RL | 功能描述:IC MCU 16/32BIT 32KB 32LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND |
| ADUC70SMARTLINKRL7 | 制造商:Analog Devices 功能描述: |
| ADUC70TEL | 制造商:Analog Devices 功能描述:FLASH ARM +5-CH 12BIT ADC - Trays |
| ADUC70TEL-RL7 | 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。