- 您現在的位置：買賣IC網 > PDF目錄1988 > AD9879BSZ (Analog Devices Inc)IC PROCESSOR FRONT END 100MQFP PDF資料下載
參數資料
| 型號： | AD9879BSZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 22/32頁 |
| 文件大小： | 0K |
| 描述： | IC PROCESSOR FRONT END 100MQFP |
| 標準包裝： | 1 |
| 位數： | 12 |
| 通道數： | 5 |
| 功率（瓦特）： | 587mW |
| 電壓 - 電源，模擬： | 3.3V |
| 電壓 - 電源，數字： | 3.3V |
| 封裝/外殼： | 100-BQFP |
| 供應商設備封裝： | 100-MQFP（14x20） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD9879
Rev. A | Page 29 of 32
GROUND PLANES
In general, if the component placing guidelines discussed in the
Component Placement section can be implemented, it is best to
have at least one continuous ground plane for the entire board.
All ground connections should be made as short as possible.
This results in the lowest impedance return paths and the
quietest ground connections.
If the components cannot be placed in a manner that keeps the
high frequency ground currents from traversing under the
MxFE and analog components, it may be necessary to put
current steering channels into the ground plane to route the
high frequency currents around these sensitive areas. These
current steering channels should be made only when and where
necessary.
SIGNAL ROUTING
The digital Rx and Tx signal paths should be kept as short as
possible. Also, these traces should have a controlled impedance
of about 50 . This prevents poor signal integrity and the high
currents that can occur during undershoot or overshoot caused
by ringing. If the signal traces cannot be kept shorter than
approximately 1.5 inches, then series termination resistors
(33 to 47 ) should be placed close to all signal sources. It is
advisable to series terminate all clock signals at their source
regardless of trace length.
The receive (I IN, Q IN, and RF IN) signals are the most
sensitive signals on the entire board. Careful routing of these
signals is essential for good receive path performance. The Rx±
signals form a differential pair and should be routed together as
a pair. By keeping the traces adjacent to each other, noise
coupled onto the signals appears as common-mode and is
largely rejected by the MxFE receive input. Keeping the driving
point impedance of the receive signal low and placing any low-
pass filtering of the signals close to the MxFE further reduces
the possibility of noise corrupting these signals.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9901KQ | IC PHASE/FREQ DISCRIMR 14-CDIP |
| AD9920ABBCZRL | IC PROCESSOR CCD 12BIT 105CSPBGA |
| AD9978BCPZRL | IC PROCESSOR CCD 14BIT 40-LFCSP |
| ADADC71KD | IC ADC 16BIT HIGH RES 32-CDIP |
| ADADC80-Z-12 | IC ADC 12BIT INTEGRATED 32-CDIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9879BSZKL1 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| AD9879-EB | 制造商:Analog Devices 功能描述:Evaluation Board For Mixed Signal Front End Set Top Box, Cable Modem 制造商:Analog Devices 功能描述:DEV TOOLS, MIXED SGNL FRONT END SET TOP , CBL MODEM - Bulk |
| AD9880 | 制造商:Analog Devices 功能描述:AUDIO PROCESSOR - Bulk |
| AD9880/PCB | 制造商:AD 制造商全稱:Analog Devices 功能描述:Analog/HDMI Dual Display Interface |
| AD9880/PCBZ | 功能描述:KIT EVALUATION AD9880 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:Advantiv® 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
發布緊急采購，3分鐘左右您將得到回復。