- 您現在的位置：買賣IC網 > PDF目錄16537 > AD9523/PCBZ (Analog Devices Inc)BOARD EVAL FOR AD9523 PDF資料下載
參數資料
| 型號： | AD9523/PCBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 15/60頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL FOR AD9523 |
| 設計資源： | AD9523(-1) Eval Board Schematic AD9523(-1) BOM AD9523(-1) Gerber Files |
| 標準包裝： | 1 |
| 主要目的： | 計時，時鐘發生器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | AD9523 |
| 主要屬性： | 板載 PLL 環路濾波器 |
| 次要屬性： | LED 狀態指示器 |
| 已供物品： | 板 |
| 相關產品： | AD9523BCPZ-REEL7-ND - IC INTEGER-N CLCK GEN 72LFCSP AD9523BCPZ-ND - IC INTEGER-N CLCK GEN 72LFCSP AD9523-1BCPZ-ND - IC INTEGER-N CLCK GEN 72LFCSP AD9523-1BCPZ-REEL7-ND - IC INTEGER-N CLCK GEN 72LFCSP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
AD9523
Data Sheet
Rev. C | Page 22 of 60
PLL1 Input Dividers
Each reference input feeds a dedicated reference divider block.
The input dividers provide division of the reference frequency
in integer steps from 1 to 1023. They provide the bulk of the
frequency prescaling that is necessary to reduce the reference
frequency to accommodate the bandwidth that is typically
desired for PLL1.
PLL1 Reference Switchover
The reference monitor verifies the presence/absence of the
prescaled REFA and REFB signals (that is, after division by the
input dividers). The status of the reference monitor guides the
activity of the switchover control logic. The AD9523 supports
automatic and manual PLL reference clock switching between
REFA (the REFA and REFA pins) and REFB (the REFB and
REFB pins). This feature supports networking and infrastructure
applications that require redundant references.
There are several configurable modes of reference switchover.
The manual switchover is achieved either via a programming
register setting or by using the REF_SEL pin. The automatic
switchover occurs when REFA disappears and there is a reference
on REFB.
The reference automatic switchover can be set to work as follows:
Nonrevertive: stay on REFB. Switch from REFA to REFB
when REFA disappears, but do not switch back to REFA
if it reappears. If REFB disappears, then go back to REFA.
Revert to REFA. Switch from REFA to REFB when REFA
disappears. Return to REFA from REFB when REFA returns.
See Table 43 for the PLL1 miscellaneous control register bit
settings.
PLL1 Holdover
In the absence of both input references, the device enters
holdover mode. Holdover is a secondary function that is
provided by PLL1. Because PLL1 has an external VCXO
available as a frequency source, it continues to operate in the
absence of the input reference signals. When the device
switches to holdover, the charge pump tristates. The device
continues operating in this mode until a reference signal
becomes available. Then the device exits holdover mode,
and PLL1 resynchronizes with the active reference. In addition
to tristate, the charge pump can be forced to VCC/2 during
holdover (see Table 43, Bit 6 in Register 0x01C).
COMPONENT BLOCKS—OUTPUT PLL (PLL2)
PLL2 General Description
The output PLL (referred to as PLL2) consists of an optional
input reference doubler, phase-frequency detector (PFD),
a partially integrated analog loop filter (see Figure 25), an
integrated voltage-controlled oscillator (VCO), and a feedback
divider. The VCO produces a nominal 3.8 GHz signal with an
output divider that is capable of division ratios of 4 to 11.
The PFD of the output PLL drives a charge pump that increases,
decreases, or holds constant the charge stored on the loop filter
capacitors (both internal and external). The stored charge
results in a voltage that sets the output frequency of the VCO.
The feedback loop of the PLL causes the VCO control voltage to
vary in a way that phase locks the PFD input signals. The gain
of PLL2 is proportional to the current delivered by the charge
pump. The loop filter bandwidth is chosen to reduce noise
contributions from PLL sources that could degrade phase noise
requirements.
The output PLL has a VCO with multiple bands spanning a
range of 3.6 GHz to 4.0 GHz. However, the actual operating
frequency within a particular band depends on the control
voltage that appears on the loop filter capacitor. The control
voltage causes the VCO output frequency to vary linearly within
the selected band. This frequency variability allows the control
loop of the output PLL to synchronize the VCO output signal
with the reference signal applied to the PFD. Typically, the
device automatically selects the appropriate band as part of its
calibration process (invoked via the VCO control register at
Address 0x0F3).
N DIVIDER
TO DIST/
RESYNC
×2
PLL1_OUT
LDO
PLL_1.8V
LDO_PLL2
VDD3_PLL2
LDO_VCO
DIVIDE BY
1, 2, 4, 8, 16
DIVIDE BY
4, 5, 6, ...11
DIVIDE-BY-4
PRESCALER
A/B
COUNTERS
CHARGE PUMP
8 BITS, 3.5A LSB
PFD
RZERO
RPOLE2
CPOLE1
CPOLE2
LF2_EXT_CAP
08439-
023
AD9523
Figure 25. Output PLL (PLL2) Block Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| VI-J4M-EZ-S | CONVERTER MOD DC/DC 10V 25W |
| VE-B1M-EX | CONVERTER MOD DC/DC 10V 75W |
| DC1562A-A | BOARD EVAL LTC6990 |
| HCM11DRAH | CONN EDGECARD 22POS R/A .156 SLD |
| ECE-P2DP562HA | CAP ALUM 5600UF 200V 20% SNAP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9524 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Jitter Cleaner and Clock Generator with 6 Differential or 13 LVCMOS Outputs |
| AD9524/PCBZ | 功能描述:BOARD EVAL FOR AD9524 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PSoC® 主要目的:電源管理，熱管理 嵌入式:- 已用 IC / 零件:- 主要屬性:- 次要屬性:- 已供物品:板，CD，電源 |
| AD9524BCPZ | 功能描述:IC INTEGER-N CLCK GEN 48LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:28 系列:- 類型:時鐘/頻率發生器 PLL:是 主要目的:Intel CPU 服務器 輸入:時鐘 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:3:22 差分 - 輸入:輸出:無/是 頻率 - 最大:400MHz 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:64-TFSOP （0.240"，6.10mm 寬） 供應商設備封裝:64-TSSOP 包裝:管件 |
| AD9524BCPZ-REEL7 | 功能描述:IC INTEGER-N CLCK GEN 48LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:28 系列:- 類型:時鐘/頻率發生器 PLL:是 主要目的:Intel CPU 服務器 輸入:時鐘 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:3:22 差分 - 輸入:輸出:無/是 頻率 - 最大:400MHz 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:64-TFSOP （0.240"，6.10mm 寬） 供應商設備封裝:64-TSSOP 包裝:管件 |
| AD9525 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Jitter Clock Generator with Eight LVPECL Outputs |
發布緊急采購，3分鐘左右您將得到回復。