- 您現在的位置：買賣IC網 > PDF目錄10537 > AD7765BRUZ (Analog Devices Inc)IC ADC 24BIT S/D 156KSPS 28TSSOP PDF資料下載
參數資料
| 型號： | AD7765BRUZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 20/33頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 24BIT S/D 156KSPS 28TSSOP |
| 標準包裝： | 50 |
| 位數： | 24 |
| 采樣率（每秒）： | 156k |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 371mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 28-TSSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個差分，單極；1 個差分，雙極 |
| 產品目錄頁面： | 779 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
AD7765
Rev. A | Page 26 of 32
DECOUPLING AND LAYOUT INFORMATION
SUPPLY DECOUPLING
The decoupling of the supplies applied to the AD7765 is
important in achieving maximum performance. Each supply
pin must be decoupled to the correct ground pin with a 100 nF,
0603 case size capacitor.
Pay particular attention to decoupling Pin 7 (AVDD2) directly to
the nearest ground pin (Pin 8). The digital ground pin, AGND2
(Pin 20) is routed directly to ground. Also, connect REFGND
(Pin 26) directly to ground.
The DVDD (Pin 17) and AVDD3 (Pin 28) supplies should be
decoupled to the ground plane at a point away from the device.
It is advised to decouple the supplies that are connected to the
following supply pins through 0603 size, 100 nF capacitors to a
star ground point linked to Pin 23 (AGND1).
VREF+ (Pin 27)
AVDD4 (Pin 25)
AVDD1 (Pin 24)
AVDD2 (Pin 21)
A layout decoupling scheme for these supplies, which connect
to the right side of the AD7765, is shown in Figure 45. Note the
star-point ground created at Pin 23.
AVDD2 (PIN 21)
VREF+ (PIN 27)
GND
PIN 23
STAR-POINT
GND
AVDD4
(PIN 25)
AVDD3 (PIN 28)
VIA TO GND
FROM PIN 20
AVDD1 (PIN 24)
GND
PIN 15
06519-
133
Figure 45. AD7765 Supply Decoupling
REFERENCE VOLTAGE FILTERING
(4.096 V), is suitable for use with the AD7765. The reference
voltage supplied to the AD7765 should be decoupled and
filtered, as shown in Figure 46.
The recommended scheme for the reference voltage supply
is a 200 Ω series resistor connected to a 100 μF tantalum
capacitor, followed by a 10 nF decoupling capacitor very close
to the VREF+ pin.
7.5V
VOUT
2
VIN
6
4
10F
100nF
+
100nF
+
ADR444
GND
VREF+
PIN 27
100F
200
06519-
134
Figure 46. Reference Connection
DIFFERENTIAL AMPLIFIER COMPONENTS
The correct components for use around the on-chip differential
amplifier are detailed in Table 7. Matching the components on
both sides of the differential amplifier is important to minimize
distortion of the signal applied to the amplifier. A tolerance of
0.1% or better is required for these components. Symmetrical
routing of the tracks on both sides of the differential amplifier
also assists in achieving stated performance. Figure 47 shows a
typical layout for the components around the differential
amplifier. Note that the traces for both differential paths are
made as symmetrical as possible and that the feedback resistors
and capacitors are placed on the underside of the PCB to enable
the simplest routing.
RFB
CFB
RIN
VINA–
VINA+
06519-
135
Figure 47. Typical Layout Structure for Surrounding Components
LAYOUT CONSIDERATIONS
While using the correct components is essential to achieving
optimum performance, the correct layout is just as important.
The AD7765 product page on www.analog.com contains the
Gerber files for the AD7765 evaluation board. These files
should be downloaded and used as a reference when designing
any system using the AD7765.
The use of ground planes should also be carefully considered.
To ensure that the return currents through the decoupling
capacitors are flowing to the correct ground pin, the ground
side of the capacitors should be as close to the ground pin
associated with that supply as recommended in the Supply
Decoupling section.
相關PDF資料 |
PDF描述 |
|---|---|
| HIN232IPZ | IC 2DRVR/2RCVR RS232 5V 16-DIP |
| TAS5711PHPR | IC AMP AUD DGTL 20W 2CH 48HTQFP |
| AD7899ARZ-1 | IC ADC 14BIT 400KSPS 5V 28SOIC |
| HIN202ECBNZ | IC 2DRVR/2RCVR RS232 5V 16-SOIC |
| HIN202CPZ | IC TXRX RS-232 5V 16-PDIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7765BRUZ-REEL7 | 功能描述:IC ADC 24BIT S/D 156KSPS 28TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7766 | 制造商:AD 制造商全稱:Analog Devices 功能描述:24-Bit, 8.5 mW, 109 dB, 128/64/32 kSPS ADCs |
| AD7766-1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:24-Bit, 8.5 mW, 109 dB, 128/64/32 kSPS ADCs |
| AD7766-2 | 制造商:AD 制造商全稱:Analog Devices 功能描述:24-Bit, 8.5 mW, 109 dB, 128/64/32 kSPS ADCs |
| AD7766BRUZ | 功能描述:IC ADC 24BIT 128KSPS SAR 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
發布緊急采購，3分鐘左右您將得到回復。