
Philips Semiconductors
Preliminary specification
87LPC769
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP 8-bit A/D, and DAC
2000 Apr 26
51
DC ELECTRICAL CHARACTERISTICS
V
DD
= 4.5 V to 5.5 V unless otherwise specified; T
amb
= –45
°
C to +125
°
C or –45
°
C to +85
°
C, unless otherwise specified.
SYMBOL
PARAMETER
TEST CONDITIONS
LIMITS
TYP
1
15
6
1
UNIT
MIN
MAX
25
10
10
I
DD
I
ID
I
PD
V
RAM
V
IL
V
IL1
V
IH
V
IH1
HYS
V
OL
V
OL1
V
OH
V
OH1
C
IO
I
IL
I
LI
I
TL
R
RST
V
BO3.8
V
REF
t
C
(V
REF
)
SS
NOTES:
1. Typical ratings are not guaranteed. The values listed are at room temperature, 5 V.
2. See other Figures for details.
Active mode: I
CC(MAX)
= tbd
Idle mode: I
CC(MAX)
3. Ports in quasi-bidirectional mode with weak pull-up (applies to all port pins with pull-ups). Does not apply to open drain pins.
4. Ports in PUSH-PULL mode. Does not apply to open drain pins.
5. In all output modes except high impedance mode.
6. Port pins source a transition current when used in quasi-bidirectional mode and externally driven from 1 to 0. This current is highest when
V
IN
is approximately 2 V.
7. Measured with port in high impedance mode. Parameter is guaranteed but not tested at cold temperature.
8. Measured with port in quasi-bidirectional mode.
9. Under steady state (non-transient) conditions, I
OL
must be externally limited as follows:
Maximum I
per port pin:
20 mA
Maximum total I
OL
for all outputs:
80 mA
Maximum total I
OH
for all outputs:
5 mA
If I
exceeds the test condition, V
OL
may exceed the related specification. Pins are not guaranteed to sink current greater than the listed
test conditions.
10.Pin capacitance is characterized but not tested.
11. The I
DD
, I
ID
, and I
PD
specifications are measured using an external clock with the following functions disabled: comparators, brownout
detect, and watchdog timer.
12.Devices initially operating at V
DD
= 4.5V or above and at f
OSC
= 10 MHz or less are guaranteed to continue to execute instructions correctly
at the brownout trip point. Initial power-on operation below V
DD
= 4.5 V is not guaranteed.
Power supply current, operating
Power supply current, Idle mode
Power supply current, Power Down mode
RAM keep-alive voltage
Input low voltage (TTL input)
Negative going threshold (Schmitt input)
Input high voltage (TTL input)
Positive going threshold (Schmitt input)
Hysteresis voltage
Output low voltage all ports
5, 9
Output low voltage all ports
5, 9
Output high voltage, all ports
3
Output high voltage, all ports
4
Input/Output pin capacitance
10
Logical 0 input current, all ports
8
Input leakage current, all ports
7
Logical 1 to 0 transition current, all ports
3, 6
Internal reset pull-up resistor
Brownout trip voltage with BOV = 0
Bandgap reference voltage
Bandgap temperature coefficient
Bandgap supply sensitivity
5.0 V, 10 MHz
11
5.0 V, 10 MHz
11
5.0 V
11
mA
mA
μ
A
V
V
V
V
V
V
V
V
V
V
pF
μ
A
μ
A
μ
A
k
V
V
1.5
–0.5
4.5 V < V
DD
< 5.5 V
0.2 V
DD
–0.1
0.3 V
DD
V
DD
+0.5
V
DD
+0.5
–0.5 V
DD
0.2 V
DD
+0.9
0.7 V
DD
0.4 V
DD
0.6 V
DD
0.2 V
DD
I
OL
= 3.2 mA, V
DD
= 4.5 V
I
OL
= 20 mA, V
DD
= 4.5 V
I
OH
= –30
μ
A, V
DD
= 4.5 V
I
OH
= –1.0 mA, V
DD
= 4.5 V
0.4
1.0
V
DD
–0.7
V
DD
–0.7
15
–50
±
2
–650
225
3.90
1.41
V
IN
= 0.4 V
V
IN
= V
IL
or V
IH
V
IN
= 2.0 V at V
DD
= 5.5 V
–150
40
3.45
1.11
T
amb
= –45
°
C to +85
°
C
3.8
1.26
tbd
tbd
ppm/
°
C
%/V