參數資料
型號： 87LPC769
廠商： NXP Semiconductors N.V.
英文描述： Low power, low price, low pin count(20 pin) microcontroller with 4 kB OTP and 8-bit A/D,and DAC(帶4 kB OTP、8位A/D和D/A轉換的低功耗，低價格，少引腳（20引腳）的微控制器)
中文描述： 低功耗，低價格，低引腳數（20針）與4 KB的檢察官辦公室和8位A / D，和DAC（帶4 KB的檢察官辦公室，8位微控制器的A / D和的D / A轉換的低功耗，低價格，少引腳（20引腳）的微控制器）
文件頁數： 26/61頁
文件大?。?/td> 275K
代理商： 87LPC769
Philips Semiconductors
Preliminary specification
87LPC769
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP 8-bit A/D, and DAC
2000 Apr 26
23
I/O Ports
The 87LPC769 has 3 I/O ports, port 0, port 1, and port 2. The exact
number of I/O pins available depend upon the oscillator and reset
options chosen. At least 15 pins of the 87LPC769 may be used as
I/Os when a two-pin external oscillator and an external reset circuit
are used. Up to 18 pins may be available if fully on-chip oscillator
and reset configurations are chosen.
All but three I/O port pins on the 87LPC769 may be software
configured to one of four types on a bit-by-bit basis, as shown in
Table 4. These are: quasi-bidirectional (standard 80C51 port
outputs), push-pull, open drain, and input only. Two configuration
registers for each port choose the output type for each port pin.
Table 5. Port Output Configuration Settings
PxM1.y
PxM2.y
Port Output Mode
0
0
Quasi-bidirectional
0
1
Push-Pull
1
0
Input Only (High Impedance)
1
1
Open Drain
Quasi-Bidirectional Output
Configuration
The default port output configuration for standard 87LPC769 I/O
ports is the quasi-bidirectional output that is common on the 80C51
and most of its derivatives. This output type can be used as both an
input and output without the need to reconfigure the port. This is
possible because when the port outputs a logic high, it is weakly
driven, allowing an external device to pull the pin low. When the pin
is pulled low, it is driven strongly and able to sink a fairly large
current. These features are somewhat similar to an open drain
output except that there are three pull-up transistors in the
quasi-bidirectional output that serve different purposes.
One of these pull-ups, called the “very weak” pull-up, is turned on
whenever the port latch for the pin contains a logic 1. The very weak
pull-up sources a very small current that will pull the pin high if it is
left floating.
A second pull-up, called the “weak” pull-up, is turned on when the
port latch for the pin contains a logic 1 and the pin itself is also at a
logic 1 level. This pull-up provides the primary source current for a
quasi-bidirectional pin that is outputting a 1. If a pin that has a logic 1
on it is pulled low by an external device, the weak pull-up turns off,
and only the very weak pull-up remains on. In order to pull the pin
low under these conditions, the external device has to sink enough
current to overpower the weak pull-up and take the voltage on the
port pin below its input threshold.
The third pull-up is referred to as the “strong” pull-up. This pull-up is
used to speed up low-to-high transitions on a quasi-bidirectional port
pin when the port latch changes from a logic 0 to a logic 1. When this
occurs, the strong pull-up turns on for a brief time, two CPU clocks, in
order to pull the port pin high quickly. Then it turns off again.
The quasi-bidirectional port configuration is shown in Figure 13.
SU01159
WEAK
VERY
WEAK
STRONG
PORT
PIN
V
DD
2 CPU
CLOCK DELAY
INPUT
DATA
PORT LATCH
DATA
N
P
P
P
Figure 13. Quasi-Bidirectional Output
相關PDF資料
PDF描述
87N-1000A-0C Signal Conditioner
87N-1000A-0L Signal Conditioner
87N-1000A-0P Signal Conditioner
87N-1000A-0R Signal Conditioner
87N-1000S-4L Signal Conditioner
相關代理商/技術參數
參數描述
87MCW4MD 制造商:Siemens 功能描述:
87MCW4MF 制造商:Siemens 功能描述:
87MCW4MG 制造商:Siemens 功能描述:
87MCW4MH 制造商:Siemens 功能描述:
87MCW4MJ 制造商:Siemens 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*