- 您現在的位置：買賣IC網 > PDF目錄360515 > 7513 7513 Group Datasheet Datasheet 1067K/FEB.06.01 PDF資料下載
參數資料
| 型號： | 7513 |
| 英文描述： | 7513 Group Datasheet Datasheet 1067K/FEB.06.01 |
| 中文描述： | 7513組數據表數據表1067K/FEB.06.01 |
| 文件頁數： | 52/66頁 |
| 文件大?。?/td> | 1067K |
| 代理商： | 7513 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁當前第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
51
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
7513 Group
NOTES ON PROGRAMMING
Processor Status Register
The contents of the processor status register (PS) after a reset are
undefined, except for the interrupt disable flag (I) which is
“
1
”
. Af-
ter a reset, initialize flags which affect program execution.
In particular, it is essential to initialize the index X mode (T) and
the decimal mode (D) flags because of their effect on calculations.
Interrupt
The contents of the interrupt request bits do not change immedi-
ately after they have been written. After writing to an interrupt
request register, execute at least one instruction before perform-
ing a BBC or BBS instruction.
Decimal Calculations
To calculate in decimal notation, set the decimal mode flag (D)
to
“
1
”
, then execute an ADC or SBC instruction. After executing
an ADC or SBC instruction, execute at least one instruction be-
fore executing a SEC, CLC, or CLD instruction.
In decimal mode, the values of the negative (N), overflow (V),
and zero (Z) flags are invalid.
Timers
If a value n (between 0 and 255) is written to a timer latch, the fre-
quency division ratio is 1/(n + 1).
Multiplication and Division Instructions
The index mode (T) and the decimal mode (D) flags do not affect
the MUL and DIV instruction.
The execution of these instructions does not change the contents
of the processor status register.
Ports
The contents of the port direction registers cannot be read.
The following cannot be used:
The data transfer instruction (LDA, etc.)
The operation instruction when the index X mode flag (T) is
“
1
”
The addressing mode which uses the value of a direction regis-
ter as an index
The bit-test instruction (BBC or BBS, etc.) to a direction register
The read-modify-write instruction (ROR, CLB, or SEB, etc.) to a
direction register
Use instructions such as LDM and STA, etc., to set the port direc-
tion registers.
Serial I/O
In clock synchronous serial I/O, if the receive side is using an ex-
ternal clock and it is to output the S
RDY
signal, set the transmit
enable bit, the receive enable bit, and the S
RDY
output enable bit
to
“
1
”
.
Serial I/O1 continues to output the final bit from the T
X
D pin after
transmission is completed.
In serial I/O2, the S
OUT2
pin goes to high impedance state after
transmission is completed.
A-D Converter
The comparator uses internal capacitors whose charge will be lost
if the clock frequency is too low.
Make sure that f(X
IN
) is at least 500 kHz during an A-D conver-
sion.
Do not execute the STP or WIT instruction during an A-D conver-
sion.
Instruction Execution Time
The instruction execution time is obtained by multiplying the fre-
quency of the internal clock
φ
by the number of cycles needed to
execute an instruction.
The number of cycles required to execute an instruction is shown
in the list of machine instructions.
The frequency of the internal clock
φ
is half of the X
IN
frequency.
相關PDF資料 |
PDF描述 |
|---|---|
| 75160-101-36 | STIFTLEISTE ABTRENNBAR 1REIHIG 36POL |
| 75160-102-36 | STIFTLEISTE ABTRENNBAR 1REIHIG 36POL |
| 75160-105-36 | STIFTLEISTE ABTRENNBAR 1REIHIG 36POL |
| 75160-301-36 | STIFTLEISTE ABTRENNBAR 1REIHIG 36POL |
| 75160-302-36 | STIFTLEISTE ABTRENNBAR 1REIHIG 36POL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 75-130 | 制造商:Zierick Manufacturing Corporation 功能描述: |
| 75130-1213 | 制造商:MOLEX 功能描述: |
| 75-130477-52S | 功能描述:Circular Connector 制造商:amphenol industrial operations 系列:- 包裝:- 零件狀態:有效 連接器類型:- 針腳數:- 外殼尺寸 - 插件:- 外殼尺寸，MIL:- 安裝類型:- 端接:- 緊固類型:- 朝向:- 侵入防護:- 外殼材料，鍍層:- 觸頭鍍層:- 特性:- 觸頭鍍層厚度:- 額定電流:- 電壓 - 額定:- 工作溫度:- 標準包裝:1 |
| 75-131018-1G | 制造商:Amphenol Corporation 功能描述:75-131018-01G - Bulk |
| 75-131018-1I | 制造商:Amphenol Corporation 功能描述:75-131018-01I - Bulk |
發布緊急采購，3分鐘左右您將得到回復。