參數資料
型號： (Z)PSD813F3
英文描述： Flash In System Programmable Mirocomputer Peripherals(閃速，在系統可編程微控制器外圍器件，1M位閃速存儲器，16K位SRAM)
中文描述： Flash在系統可編程Mirocomputer外設（閃速，在系統可編程微控制器外圍器件，100萬位閃速存儲器，16K的位的SRAM）
文件頁數： 14/130頁
文件大小： 650K
代理商： (Z)PSD813F3
PSD813F Famly
Prelimnary
10
The following table describes the pin names and pin functions of the PSD813F. Pins that
have multiple names and/or functions are defined using PSD Configuration.
7.0
Table 5.
PSD813F
Pin
Descriptions
Pin Name
Pin* Type
Description
ADIO0-7
30-37
I/O
This is the lower Address/Data port. Connect your MCU
address or address/data bus according to the following rules:
1. If your MCU has a multiplexed address/data bus where
the data is multiplexed with the lower address bits,
connect AD[0:7] to this port.
2. If your MCU does not have a multiplexed address/data
bus, or you are using an 80C251 in page mode, connect
A[0:7] to this port.
3. If you are using an 80C51XA in burst mode, connect
A4/D0 through A11/D7 to this port.
ALE or AS latches the address. The PSD drives data out only
if the read signal is active and one of the PSD functional
blocks was selected. The addresses on this port are passed
to the PLDs.
ADIO8-15
39-46
I/O
This is the upper Address/Data port. Connect your MCU
address or address/data bus according to the following rules:
1. If your MCU has a multiplexed address/data bus where
the data is multiplexed with the lower address bits,
connect A[8:15] to this port.
2. If your MCU does not have a multiplexed address/data
bus, connect A[8:15] to this port.
3. If you are using an 80C251 in page mode, connect
AD[8:15] to this port.
4. If you are using an 80C51XA in burst mode, connect
A12/D8 through A19/D15 to this port.
ALE or AS latches the address. The PSD drives data out only
if the read signal is active and one of the PSD functional
blocks was selected. The addresses on this port are passed
to the PLDs.
CNTL0
47
I
The following control signals can be connected to this port,
based on your MCU:
1. WR — active-low write input.
2. R_W — active-high read/active low write input.
This port is connected to the PLDs. Therefore, these signals
can be used in decode and other logic equations.
CNTL1
50
I
The following control signals can be connected to this port,
based on your MCU:
1. RD — active-low read input.
2. E — E clock input.
3. DS — active-low data strobe input.
4. PSEN — connect PSEN to this port when it is being used
as an active-low read signal. For example, when the
80C251 outputs more than 16 address bits, PSEN is
actually the read signal.
This port is connected to the PLDs. Therefore, these
signals can be used in decode and other logic equations.
相關PDF資料
PDF描述
(Z)PSD813F2(中文) Flash In System Programmable Mirocomputer Peripherals(閃速，在系統可編程微控制器外圍器件，1M位和256K位閃速存儲器，16K位SRAM)
(Z)PSD813F3R(中文) Multi-Chip-Module to Monolithic Flash PSD(閃速，在系統可編程微控制器外圍器件，0M位閃速存儲器，無SRAM)
(Z)PSD813F2 Flash In System Programmable Mirocomputer Peripherals(閃速，在系統可編程微控制器外圍器件，1M位和256K位閃速存儲器，16K位SRAM)
(Z)PSD813F3R Multi-Chip-Module to Monolithic Flash PSD(閃速，在系統可編程微控制器外圍器件，0M位閃速存儲器，無SRAM)
1.5KA24A AUTOMOTIVE TRANSIENT VOLTAGE SUPPRESSOR
相關代理商/技術參數
參數描述
ZPSD813F3-12JI 制造商:WSI 功能描述:
ZPSD813F3-15J 制造商:STMicroelectronics 功能描述:Flash in-system programmable microcontroller peripheral device
ZPSD813F3V-15J 制造商:WSI 功能描述:
ZPSD813F3V-A-15J 制造商:WSI 功能描述:
ZPSD813F4-12JI 制造商:WSI 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*