參數資料
型號： XRT86VL30IV80-F
廠商： Exar Corporation
文件頁數： 148/175頁
文件大?。?/td> 0K
描述： IC FRAMR/LIU T1/E1/J1 QD 80LQFP
標準包裝： 90
控制器類型： T1/E1/J1 調幀器，LIU
電源電壓： 3.3V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 80-LQFP
供應商設備封裝： 80-LQFP（12x12）
包裝： 托盤
其它名稱： 1016-1486
XRT86VL30IV80-F-ND
XRT86VL30
69
SINGLE T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION
REV. 1.0.1
2
Tx_IDLE
R/W
0
Transmit Idle (Flag Sequence Byte)
This bit configures the Transmit HDLC Controller Block #3 to unconditionally
transmit a repeating string of Flag Sequence octets (0X7E) in the data link
channel to the Remote terminal. In normal conditions, the Transmit HDLC
Controller block will repeatedly transmit the Flag Sequence octet whenever
there is no MOS message to transmit to the remote terminal equipment.
However, if the user invokes this “Transmit Idle Sequence” feature, then the
Transmit HDLC Controller block will UNCONDITIONALLY transmit a repeat-
ing stream of the Flag Sequence octet (thereby overwriting all outbound
MOS data-link messages).
0 - Configures the Transmit HDLC Controller Block # 3 to transmit data-link
information in a “normal” manner.
1 - Configures the Transmit HDLC Controller block # 3 to transmit a repeat-
ing string of Flag Sequence Octets (0x7E).
NOTE: This bit is ignored if the Transmit HDLC3 controller is operating in the
BOS Mode - bit 0 (MOS/BOS) within this register is set to 0.
1
Tx_FCS_EN
R/W
0
Transmit LAPD Message with Frame Check Sequence (FCS)
This bit permits the user to configure the Transmit HDLC Controller block # 3
to compute and append FCS octets to the “back-end” of each outbound
MOS data-link message.
0 - Configures the Transmit HDLC Controller block # 3 to NOT compute and
append the FCS octets to the back-end of each outbound MOS data-link
message.
1 - Configures the Transmit HDLC Controller block # 3 TO COMPUTE and
append the FCS octets to the back-end of each outbound MOS data-link
message.
NOTE:
This bit is ignored if the transmit HDLC3 controller has been
configured to operate in the BOS mode - bit 0 (MOS/BOS) within this
register is set to 0.
0
MOS/BOS
R/W
0
Message Oriented Signaling/Bit Oriented Signaling Send
This bit permits the user to enable LAPD transmission through HDLC Con-
troller Block # 3 using either BOS (Bit-Oriented Signaling) or MOS (Mes-
sage-Oriented Signaling) frames.
0 - Transmit HDLC Controller block # 3 BOS message Send.
1 - Transmit HDLC Controller block # 3 MOS message Send.
NOTE: This is not an Enable bit. This bit must be set to "0" each time a BOS
is to be sent.
TABLE 52: DATA LINK CONTROL REGISTER (DLCR3)
HEX ADDRESS: 0X0153
BIT
FUNCTION
TYPE
DEFAULT
DESCRIPTION-OPERATION
相關PDF資料
PDF描述
KSZ8841-32MVL IC MAC CTRLR 32BIT 128-LQFP
PIC16F684T-E/ST IC PIC MCU FLASH 2KX14 14TSSOP
LTC4267CDHC#PBF IC POE 802.3AF INTERFACE 16-DFN
PIC16C505-04E/P IC MCU OTP 1KX12 14DIP
LTC4264IDE#PBF IC CNTRLR PD INTERFACE 12-DFN
相關代理商/技術參數
參數描述
XRT86VL30IVF 制造商:Exar Corporation 功能描述:
XRT86VL30IV-F 功能描述:網絡控制器與處理器 IC 1-Ch T1/E1/J1 RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT86VL30IV-F 制造商:Exar Corporation 功能描述:T1/E1 Framer Combo IC
XRT86VL32 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION
XRT86VL32_07 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL T1/E1/J1 FRAMER/LIU COMBO - E1 REGISTER DESCRIPTION
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*