TABLE
參數資料
型號： XRT86VL30IV80-F
廠商： Exar Corporation
文件頁數： 109/175頁
文件大?。?/td> 0K
描述： IC FRAMR/LIU T1/E1/J1 QD 80LQFP
標準包裝： 90
控制器類型： T1/E1/J1 調幀器，LIU
電源電壓： 3.3V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 80-LQFP
供應商設備封裝： 80-LQFP（12x12）
包裝： 托盤
其它名稱： 1016-1486
XRT86VL30IV80-F-ND
XRT86VL30
34
REV. 1.0.1
SINGLE T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION
TABLE 20: SLIP BUFFER CONTROL REGISTER (SBCR)
HEX ADDRESS: 0X0116
BIT
FUNCTION
TYPE
DEFAULT
DESCRIPTION-OPERATION
7
TxSB_ISFIFO
R/W
0
Transmit Slip Buffer Mode
This bit permits the user to configure the Transmit Slip Buffer to function as
either “Slip-Buffer” Mode, or as a “FIFO”, as depicted below.
0 - Configures the Transmit Slip Buffer to function as a “Slip-Buffer”.
1 - Configures the Transmit Slip Buffer to function as a “FIFO”.
NOTE: Transmit slip buffer is only used in high-speed or multiplexed mode
where TxSERCLKn must be configured as inputs only. Users must
make sure that the “Transmit Direction” timing (i.e. TxMSYNC) and
the TxSerClk input clock signal are synchronous to prevent any
transmit slips from occuring.
NOTE: The data latency is dictated by FIFO Latency in the FIFO Latency
Register (register 0x0117).
6-5
Reserved
-
Reserved
4
SB_FORCESF
R/W
0
Force Signaling Freeze
This bit permits the user to freeze any signaling update on the RxSIGn output
pin as well as the Receive Signaling Array Register -RSAR (0x0500-0x051F)
until this bit is cleared.
0 = Signaling on RxSIG and RSAR is updated immediately.
1 = Signaling on RxSIG and RSAR is not updated until this bit is set to ‘0’.
3
SB_SFENB
R/W
0
Signal Freeze Enable Upon Buffer Slips
This bit enables signaling freeze for one multiframe after the receive buffer
slips.
If signaling freeze is enabled, then the “Receive Channel” will freeze all sig-
naling updates on RxSIG pin and RSAR (0x0500-0x051F) for at least “one-
multiframe” period, after a “slip-event” has been detected within the “Receive
Slip Buffer”.
0 = Disables signaling freeze for one multi-frame after receive buffer slips.
1 = Enables signaling freeze for one multi-frame after receive buffer slips.
2
SB_SDIR
R/W
1
Slip Buffer (RxSync) Direction Select
This bit permits user to select the direction of the receive frame boundary
(RxSYNC) signal if the receive buffer is enabled. (i.e. SB_ENB[1:0] = 01 or
10). If slip buffer is bypassed, RxSYNC is always an output pin.
0 = Selects the RxSync signal as an output
1 = Selects the RxSync signal as an input
相關PDF資料
PDF描述
KSZ8841-32MVL IC MAC CTRLR 32BIT 128-LQFP
PIC16F684T-E/ST IC PIC MCU FLASH 2KX14 14TSSOP
LTC4267CDHC#PBF IC POE 802.3AF INTERFACE 16-DFN
PIC16C505-04E/P IC MCU OTP 1KX12 14DIP
LTC4264IDE#PBF IC CNTRLR PD INTERFACE 12-DFN
相關代理商/技術參數
參數描述
XRT86VL30IVF 制造商:Exar Corporation 功能描述:
XRT86VL30IV-F 功能描述:網絡控制器與處理器 IC 1-Ch T1/E1/J1 RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT86VL30IV-F 制造商:Exar Corporation 功能描述:T1/E1 Framer Combo IC
XRT86VL32 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION
XRT86VL32_07 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL T1/E1/J1 FRAMER/LIU COMBO - E1 REGISTER DESCRIPTION
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*