- 您現在的位置：買賣IC網 > PDF目錄1976 > XRT73LC03AIV-F (Exar Corporation)IC LIU E3/DS3/STS-1 3CH 120LQFP PDF資料下載
參數資料
| 型號： | XRT73LC03AIV-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 51/61頁 |
| 文件大小： | 0K |
| 描述： | IC LIU E3/DS3/STS-1 3CH 120LQFP |
| 標準包裝： | 72 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 3/3 |
| 規程： | DS3，E3，STS-1 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 120-LQFP |
| 供應商設備封裝： | 120-LQFP（14x20） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁當前第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁
XRT73LC03A
53
REV. 1.0.4
3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
(n) = 0, 1 or 2. The associated addresses for each
channel are presented in , (repeated as Table 7).
NOTE: The default value for each of the bit-fields within
these register is "0".
5.2
DESCRIPTION OF BIT-FIELDS FOR EACH COM-
MAND
REGISTER
5.2.1
Command Register - CR0-(n)
The bit-format and default values for Command Reg-
ister CR0-(n) are listed below followed by the function
of eah of these bit-fields.
Bit D4 - RLOL_(n) (Receive Loss of Lock Status -
Channel(n))
This Read-Only bit-field reflects the lock status of the
Channel(n) Clock Recovery Phase-Locked-Loop
This bit-field is set to “0” if the Channel(n) Clock Re-
covery PLL is in lock with the incoming line signal.
This bit-field is set to "1" if the Clock Recovery PLL is
out of lock with the incoming line signal.
Bit D3 - RLOS_(n) (Receive Loss of Signal Status -
Channel(n))
This Read-Only bit-field indicates whether or not the
Channel(n) of the Receiver is currently declaring an
LOS (Loss of Signal) Condition.
This bit-field is set to "0" if Channel(n) is not currently
declaring the LOS Condition.
This bit-field is set to "1" if Channel(n) is declaring an
LOS Condition.
Bit D2 - ALOS_(n) (Analog Loss of Signal Status -
Channel(n))
This Read-Only bit-field indicates whether or not the
Channel(n) Analog LOS Detector is currently declar-
ing an LOS condition.
This bit-field is set to "0" if the Analog LOS Detector
within Channel(n) is NOT currently declaring an LOS
condition. This bit-field is set to "1" if the Analog LOS
Detector is currently declaring an LOS condition.
NOTE: The purpose is to isolate the Detector (e.g., either
the Analog LOS or the Digital LOS detector) that is declar-
ing the LOS condition. This feature may be useful for trou-
bleshooting/debugging purposes
Bit D1 - DLOS_(n) (Digital Loss of Signal Status -
Channel(n))
This Read-Only bit-field indicates whether or not the
Channel(n) Digital LOS Detector is currently declar-
ing an LOS condition.
This bit-field is set to "0" if the Channel(n) Digital LOS
Detector is NOT currently declaring an LOS condi-
tion. This bit-field is set to "1" if the Channel(n) Digital
LOS Detector is currently declaring an LOS condition.
NOTE: The purpose is to isolate the Detector (e.g., either
the Analog LOS or the Digital LOS detector) that is declar-
ing the LOS condition. This feature may be useful for trou-
bleshooting/debugging purposes.
Bit D0 - DMO_(n) (Drive Monitor Output Status -
Channel(n))
This Read-Only bit-field reflects the status of the
DMO output pin.
5.2.2
Command Register CR1
The bit-format and default values for Command Reg-
ister CR1-(n) are listed below followed by the function
of each of these bit-fields..
Bit D4 - TxOFF_(n) (Transmitter OFF - Channel(n))
This Read/Write bit-field is used to turn off the Chan-
nel(n) Transmitter.
Writing a "1" to this bit field turns off the Transmitter
and tri-state the Transmit Output. Writing a "0" to this
bit-field turns on the Transmitter.
Bit D3 - TAOS_(n) (Transmit All OneS - Chan-
nel(n))
This Read/Write bit-field is used to command the
Channel(n) Transmitter to generate and transmit an
all “1’s” pattern onto the line.
Writing a "1" to this bit-field commands the Transmit-
ter to transmit an all “1’s” pattern onto the line. Writ-
ing a "0" to this bit-field commands normal operation.
Bit D2 - TxClkINV_(n) (Transmit Clock Invert -
Channel(n))
This Read/Write bit-field is used to configure the
Transmitter to sample the signal at the TPData and
TNData pins on the rising edge or falling edge of Tx-
Clk (the Transmit Line Clock signal).
Writing a "1" to this bit-field configures the Transmitter
to sample the TPData and TNData input pins on the
rising edge of TxClk. Writing a “0" to this bit-field con-
COMMAND REGISTER CR0-(n)
D4
D3
D2
D1
D0
RLOL_(n) RLOS_(n) ALOS_(n) DLOS_(n) DMO_(n)
11
1
COMMAND REGISTER CR1-(n)
D4
D3
D2
D1
D0
TxOFF_(n) TAOS_(n) TxClkINV_(n) TxLEV_(n) TxBIN_(n)
00
0
相關PDF資料 |
PDF描述 |
|---|---|
| XRT73LC04AIV-F | IC LIU E3/DS3/STS-1 4CH 144LQFP |
| XRT73R06IB-F | IC LIU E3/DS3/STS-1 6CH 217BGA |
| XRT73R12IB-L | IC LIU E3/DS3/STS-1 12CH 420TBGA |
| XRT75L00DIV-F | IC LIU E3/DS3/STS-1 SGL 52TQFP |
| XRT75L00IV-F | IC LIU E3/DS3/STS-1 SGL 52TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT73LC04A | 制造商:EXAR 制造商全稱:EXAR 功能描述:4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT |
| XRT73LC04A_08 | 制造商:EXAR 制造商全稱:EXAR 功能描述:4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT |
| XRT73LC04AES | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| XRT73LC04AIV | 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT73LC04AIV-F | 功能描述:外圍驅動器與原件 - PCI 4-Ch DS3, E3, STS-1 RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。