參數資料
型號: XRT73LC03AIV-F
廠商: Exar Corporation
文件頁數: 40/61頁
文件大小: 0K
描述: IC LIU E3/DS3/STS-1 3CH 120LQFP
標準包裝: 72
類型: 線路接口裝置(LIU)
驅動器/接收器數: 3/3
規程: DS3,E3,STS-1
電源電壓: 3.135 V ~ 3.465 V
安裝類型: 表面貼裝
封裝/外殼: 120-LQFP
供應商設備封裝: 120-LQFP(14x20)
包裝: 托盤
XRT73LC03A
43
REV. 1.0.4
3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
forced to "0". Once the LOS condition has been
cleared, then the channel(n) resumes normal trans-
mission of the recovered data to the Receiving Termi-
nal.
This feature is available whenever XRT73LC03A is
operating in the HOST Mode or Hardware Mode.
a. Operating in the Hardware Mode.
The Muting upon LOS feature is enabled by pulling
the LOSMUTEN output pin “High". This enables the
Muting upon LOS feature globally for all channels.
b. Operating in the HOST Mode.
The Muting upon LOS feature for each Channel can
be enabled by writing a "1" into the LOSMUT_(n) bit-
field within Command Register 3.
NOTE: This step only enables the Muting upon LOS feature
within Channel(n).
3.6
ROUTING THE RECOVERED TIMING AND DATA
INFORMATION TO THE RECEIVING TERMINAL
EQUIPMENT
Each channel takes the Recovered Timing and Data
information, converts it into CMOS levels and routes
it to the Receiving Terminal Equipment via the
RPOS_(n), RNEG_(n) and RxClk_(n) output pins.
Each channel can deliver the recovered data and
clock information to the Receiving Terminal in either a
Single-Rail or Dual-Rail format.
3.6.1
Routing Dual-Rail Format Data to the
Receiving Terminal Equipment
Whenever a channel delivers Dual-Rail format to the
Terminal Equipment, it does so via the following sig-
nals.
RPOS_(n)
RNEG_(n)
RxClk_(n)
Figure 28 illustrates the typical interface for the trans-
mission of data in a Dual-Rail Format from the Re-
ceive Section of a channel to the Receiving Terminal
Equipment.
.
The manner that a given channel transmits Dual-Rail
data to the Receiving Terminal Equipment is de-
scribed below and illustrated in Figure 29. Each
COMMAND REGISTER CR3-(n)
D4
D3
D2
D1
D0
(SR/DR)_(n)
LOSMUT_(n)
RxOFF_(n)
RxClk_(n)INV
Reserved
X
1
xxx
FIGURE 28. THE TYPICAL INTERFACE FOR THE TRANSMISSION OF DATA IN A DUAL-RAIL FORMAT,
FROM THE
RECEIVE SECTION OF THE XRT73LC03A TO THE RECEIVING TERMINAL EQUIPMENT
Terminal
Equipment
(E3/DS3 or STS-1
Framer)
Exar E3/DS3/STS-1 LIU
Receive
Logic
Block
RxPOS
RxNEG
RxClk
RPOS
RNEG
RxClk
相關PDF資料
PDF描述
XRT73LC04AIV-F IC LIU E3/DS3/STS-1 4CH 144LQFP
XRT73R06IB-F IC LIU E3/DS3/STS-1 6CH 217BGA
XRT73R12IB-L IC LIU E3/DS3/STS-1 12CH 420TBGA
XRT75L00DIV-F IC LIU E3/DS3/STS-1 SGL 52TQFP
XRT75L00IV-F IC LIU E3/DS3/STS-1 SGL 52TQFP
相關代理商/技術參數
參數描述
XRT73LC04A 制造商:EXAR 制造商全稱:EXAR 功能描述:4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
XRT73LC04A_08 制造商:EXAR 制造商全稱:EXAR 功能描述:4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
XRT73LC04AES 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT73LC04AIV 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT73LC04AIV-F 功能描述:外圍驅動器與原件 - PCI 4-Ch DS3, E3, STS-1 RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray