- 您現在的位置：買賣IC網 > PDF目錄1976 > XRT73LC00AIV-F (Exar Corporation)IC LIU STS1/DS3/E3 SGL 44TQFP PDF資料下載
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁
XRT73LC00A
21
E3/DS3/STS-1 LINE INTERFACE UNIT
REV. 1.0.2
SYSTEM DESCRIPTION
A functional block diagram of the XRT73LC00A E3/DS3/STS-1 Transceiver IC (see Figure 1) shows that the
device contains three distinct sections:
The Transmit Section
The Receive Section
The Microprocessor Serial Interface
THE TRANSMIT SECTION
The Transmit Section accepts TTL/CMOS level signals from the Terminal Equipment in either a Single-Rail or
Dual-Rail format. The Transmit Section then takes this data and does the following:
Encodes the data into the B3ZS format if the DS3 or SONET STS-1 Modes have been selected or into the
HDB3 format if the E3 Mode has been selected.
Converts the CMOS level B3ZS or HDB3 encoded data into pulses with shapes that are compliant with the
various industry standard pulse template requirements.
Drives these pulses onto the line via the TTIP and TRING output pins across a 1:1 Transformer.
NOTE: The Transmit Section drives a "1" (or a Mark) on the line by driving either a positive or negative polarity pulse across
the 1:1 Transformer within a given bit period. The Transmit Section drives a "0" (or a Space) onto the line by driving
no pulse onto the line.
THE RECEIVE SECTION
The Receive Section receives a bipolar signal from the line either via a 1:1 Transformer or a 0.01mF Capacitor.
As the Receive Section receives this line signal it does the following:
Adjusts the signal level through an AGC circuit.
Optionally equalizes this signal for cable loss.
Attempts to quantify a bit-interval within the line signal as either a “1”, “-1” or a “0” by slicing this data. This
sliced data is used by the Clock Recovery PLL to recover the timing element within the line signal.
The sliced data is routed to the HDB3/B3ZS Decoder, during which the original data content as transmitted
by the Remote Terminal Equipment is restored to its original content.
Outputs the recovered clock and data to the Local Terminal Equipment in the form of CMOS level signals via
the RPOS, RNEG, RCLK1 and RCLK2 output pins.
THE MICROPROCESSOR SERIAL INTERFACE
The XRT73LC00A can be configured to operate in either the Hardware Mode or the HOST Mode.
The Hardware Mode
Connect the HOST/HW input pin (pin 18) to GND to configure the XRT73LC00A to operate in the Hardware
Mode.
When the XRT73LC00A is operating in the Hardware Mode, the following is true:
1. The Microprocessor Serial Interface block is
disabled.
2. The XRT73LC00A is configured via input pin settings.
Each of the pins associated with the Microprocessor Serial Interface takes on their alternative role as defined
in Table 1.
相關PDF資料 |
PDF描述 |
|---|---|
| XRT73LC03AIV-F | IC LIU E3/DS3/STS-1 3CH 120LQFP |
| XRT73LC04AIV-F | IC LIU E3/DS3/STS-1 4CH 144LQFP |
| XRT73R06IB-F | IC LIU E3/DS3/STS-1 6CH 217BGA |
| XRT73R12IB-L | IC LIU E3/DS3/STS-1 12CH 420TBGA |
| XRT75L00DIV-F | IC LIU E3/DS3/STS-1 SGL 52TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT73LC00AIVTR | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| XRT73LC00AIVTR-F | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| XRT73LC00IV | 制造商:EXAR 制造商全稱:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT73LC03A | 制造商:EXAR 制造商全稱:EXAR 功能描述:3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT |
| XRT73LC03A_08 | 制造商:EXAR 制造商全稱:EXAR 功能描述:3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT |
發布緊急采購，3分鐘左右您將得到回復。