參數資料
型號： XR17V254IV-0A-EVB
廠商： Exar Corporation
文件頁數： 19/70頁
文件大?。?/td> 0K
描述： EVAL BOARD FOR XR17V254 144LQFP
標準包裝： 1
系列： *
XR17V254
26
66MHZ PCI BUS QUAD UART WITH POWER MANAGEMENT SUPPORT
REV. 1.0.1
generators for standard or custom rates. Typically, the oscillator connections are shown in Figure 10. For
further reading on oscillator circuit please see application note DAN108 on EXAR’s web site.
3.0
TRANSMIT AND RECEIVE DATA
There are two methods to load transmit data and unload receive data from each UART channel. First, there is
a transmit data register and receive data register for each UART channel as shown in Table 5 set to ease
programming. These registers support 8, 16, 24 and 32 bits wide format. In the 32-bit format, it increases the
data transfer rate on the PCI bus. Additionally, a special register location provides receive data byte with its
associated error flags. This is a 16-bit or 32-bit read operation where the Line Status Register (LSR) content in
the UART channel register is paired along with the data byte. This operation further facilitates data unloading
with the error flags without having to read the LSR register separately. Furthermore, the XR17V254 supports
PCI burst mode for read/write operation of up to 64 bytes of data.
The second method is through each UART channel’s transmit holding register (THR) and receive holding
register (RHR). The THR and RHR registers are 16550 compatible so their access is limited to 8-bit format.
The software driver must separately read the LSR content for the associated error flags before reading the
data byte.
3.1
FIFO DATA LOADING AND UNLOADING IN 32-BIT FORMAT
The XR17V254 supports PCI Burst Read and PCI Burst Write transactions anywhere in the mapped memory
region (except reserved areas). In addition, to utilize this feature fully, the device provides a separate memory
location (apart from the individual channel’s register set) where the RX and the TX FIFO can be read from/
written to, as shown in Table 5. The following is an extract from the table showing the burstable memory
locations:
Channel N: (for channels 0 through 3) where M = 2N + 1.
RX FIFO
:
0xM00 - 0xM3F (64 bytes)
TX FIFO
:
0xM00 - 0xM3F (64 bytes)
RX FIFO + status
:
0xM80 - 0xMFF (64 bytes data + 64 bytes status)
For example, the locations for channel 2 are:
Channel 2:
RX FIFO
:
0x500 - 0x53F (64 bytes)
TX FIFO
:
0x500 - 0x53F (64 bytes)
RX FIFO + status
:
0x580 - 0x5FF (64 bytes data + 64 bytes status)
FIGURE 10. TYPICAL OSCILLATOR CONNECTIONS
C1
22-47pF
C2
22-47pF
14.7456
MHz
XTAL1
XTAL2
R=300K to 400K
相關PDF資料
PDF描述
RPS0J102MCN1GS CAP ALUM 1000UF 6.3V 20% SMD
EMM10DRMN CONN EDGECARD 20POS .156 WW
GBA31DRMN-S288 CONN EDGECARD 62POS .125 EXTEND
CM100505-18NGL INDUCTOR CHIP 18NH 1005 SMD
1-6828247-5 CA,SM,MTRJ-SC
相關代理商/技術參數
參數描述
XR17V254IV-F 功能描述:UART 接口集成電路 66MHz Quad PCI UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR17V258 制造商:EXAR 制造商全稱:EXAR 功能描述:66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
XR17V258_08 制造商:EXAR 制造商全稱:EXAR 功能描述:66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
XR17V258IV 功能描述:UART 接口集成電路 66MHz Octal PCI UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR17V258IV-0A-EVB 功能描述:UART 接口集成電路 Supports V258 144 ld TQFP, PCI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*