- 您現在的位置：買賣IC網 > Datasheet目錄58 > XIB-R (Digi International/Maxstream)BOARD INTERFACE RS232/485 Datasheet資料下載
參數資料
| 型號： | XIB-R |
| 廠商： | Digi International/Maxstream |
| 文件頁數： | 24/36頁 |
| 文件大?。?/td> | 826K |
| 描述： | BOARD INTERFACE RS232/485 |
| 標準包裝： | 1 |
| 附件類型： | 接口板 |
| 適用于相關產品： | XStream 和 Xcite 收音機 |
| 其它名稱： | Q2231853 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
9XCite"燨EM燫F燤odule?燩roduct燤anual爒2.1燵2007.01.04]
2007燤axStream,營nc.
牋牋?4
HT (Time before Wake-up Initializer) Parameter
<Non-AT Settable Parameter: Sleep (Low Power)> If any modems within range are running in a
"Cyclic Sleep Setting", a wake-up initializer must be sent by the transmitter for the other radio
modems to synchronize to the transmitter [see LH ("Wake-up Initializer Timer") Command]. When
a receiving radio modem in Cyclic Sleep wakes, it must detect the wake-up initializer portion of the
RF packet in order to synchronize to the transmitter and receive data. HT Parameter sets time
period of inactivity (no serial or RF data is sent or received) before a Wake-up Initializer is sent.
Base station tracks awake-status of remote radios. HT of base radio should be set shorter than ST
(Time before Sleep) of remote radios.
From the receiver perspective, after "HT" time elapses and the ST (Time before Sleep) Parameter
is met, the receiver goes into cyclic sleep. Once in cyclic sleep, the radio modem must first detect
the wake-up initializer and synchronize to the transmitter before it can receive data. Thus, when
time "HT" time elapses, the transmitter then knows it needs to send a long wake-up initializer for
all receivers to be able to synchronize to its next transmission. Matching "HT" to the "ST" time on
the receiver(s) guarantees that all receivers will detect the next transmission.
Parameter Range: 0 - 0xFFFF [x 100 ms]
# of bytes returned: 2
Default Parameter Value: 0xFFFF (long wake-up initializer will not be sent)
Related Parameters: LH (Wake-up Initializer Timer), SM (Sleep Mode), ST (Time before Sleep)
HV (Hardware Version) Command
<AT Command: Diagnostic> Reads and returns the hardware version of the module.
AT Command: HV
Parameter Range: 0 - 0xFFFF [Read-only]
# of bytes returned: 2
ID (Modem VID) Parameter
<Non-AT Settable Parameter: Networking> ID Parameter reads and edits the module's VID. VID is
a MaxStream-specific acronym that stands for "Vendor Identification Number". RF modules can
only communicate with other modems having the same VID.
Parameter Range: 0 - 0x7FFF (above this range is Read-only)
# of bytes returned: 2
Default Parameter Value: 0x3332
相關PDF資料 |
PDF描述 |
|---|---|
| ZMN2400HPDB | BOARD ROUTER DEV ZIGBEE 100MW |
| ZMN24HPDK-B | KIT DEV W/ZIGBEE ZMN2400HP |
| ZNI1000TC | IC TEMP SENSOR NI1000 SOT23-3 |
| 02110102-000 | SNSR TILT RATIO 60DEG 500MA FLNG |
| 1-5209285-2 | FOPC BOA 12DB FC/UPC BP SM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XIB-U | 功能描述:界面模塊 USB interface board 24XStream 9XCite RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度: |
| XIC25040 | 制造商:XIC 功能描述:25040 24HR '6 |
| XILINXPWR-079 | 功能描述:電源管理IC開發工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| XILINXPWR-080 | 功能描述:電源管理IC開發工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| XILINXPWR-081 | 功能描述:電源管理IC開發工具 Pwr Mgmt Eval Mod Xilinx RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。