參數資料
型號： XIB-R
廠商： Digi International/Maxstream
文件頁數： 17/36頁
文件大?。?/td> 826K
描述： BOARD INTERFACE RS232/485
標準包裝： 1
附件類型： 接口板
適用于相關產品： XStream 和 Xcite 收音機
其它名稱： Q2231853
9XCite"燨EM燫F燤odule?燩roduct燤anual爒2.1燵2007.01.04]
2007燤axStream,營nc.
牋牋?7
3.3. Command Reference Tables
XCite AT Commands [below] and Non-AT Settable Parameters [next page] are organized under the
following
command categories:
" AT Command Mode Options
" Diagnostic
" Networking
" Serial Interfacing
" Sleep Mode (Low Power)
Table?01.   AT燙ommands
(Settable/Readable爑sing燲CTU燬oftware,爏erial燾ommunications爏oftware爋r爉icrocontroller)
AT  
Designator
Command Name & Description
Parameter Range
Command  
Category
# Bytes
Returned
Factory
Default
CD
 DI3 Configuration. Redefines the RX LED I/O line
(RX LED signal).
0  2
0 = RX LED
1 = high
2 = low
Serial
Interfacing
1
0
CN
Exit AT Command Mode. Explicitly exit radio modem from AT
Command Mode and return it to Idle Mode.
--
AT Command
Mode Options
--
--
CS
DO2 Configuration. Select behavior of DI2 (Digital Output 2)
between CTS and RS-485 options.
0  4
0 = normal CTS
1 = RS-485 enable low
2 = high
3 = RS-485 enable high
4 = low
Serial
Interfacing
1
0
DB
Receive Signal Strength. Returns the signal strength (in
decibels) of the last received packet.
0x25  0x6A
[Read-only]
Diagnostic
1
--
DT
Destination Address. Set the address that identifies the
destination of the RF packet. Only radio modems having
matching addresses can communicate with each other.
 0  0xFFFF
Networking
2
0
FH
Force Wake-up Initializer. Force a Wake-up Initializer to be
sent on the next transmission. WR (Write) Command does not
need to be issued with FH Command.
Use only with cyclic sleep modes (SM = 3-8) active on remote
modems.
--
Sleep
(Low Power)
--
--
HP
Channel *. Select Hopping or Single Frequency channel on
which the radio modem is to communicate. Channels are not
noninterfering.
Hopping:
0  6
Single Frequency):
0  0x18
Networking
1
0
HV
Hardware Version. Read the hardware version of the modem.
Range: 0  0xFFFF
[Read-only]
Diagnostic
2
--
MK
Address Mask. Set address mask to configure local and
global address space.
0  0xFFFF
Networking
2
0xFFFF
(65535d)
RE
Restore Defaults. Restore AT-settable parameters to the
factory default configuration.
--
(Special)
--
--
SH
Serial Number High. Read High 16 bits of unique serial
number of radio modem.
0  0xFFFF
[Read-only]
Diagnostic
2
--
SL
Serial Number Low. Read Low 16 bits of unique serial number
of radio modem.
0  0xFFFF
[Read-only]
Diagnostic
2
--
VR
Firmware Version. Read firmware version currently loaded on
radio modem.
0  0xFFFF
[Read-only]
Diagnostic
2
--
WR
Write. Write parameters to radio modems non-volatile
memory in order for changes to persist through next power-up
or reset.
--
(Special)
--
--
相關PDF資料
PDF描述
ZMN2400HPDB BOARD ROUTER DEV ZIGBEE 100MW
ZMN24HPDK-B KIT DEV W/ZIGBEE ZMN2400HP
ZNI1000TC IC TEMP SENSOR NI1000 SOT23-3
02110102-000 SNSR TILT RATIO 60DEG 500MA FLNG
1-5209285-2 FOPC BOA 12DB FC/UPC BP SM
相關代理商/技術參數
參數描述
XIB-U 功能描述:界面模塊 USB interface board 24XStream 9XCite RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度:
XIC25040 制造商:XIC 功能描述:25040 24HR '6
XILINXPWR-079 功能描述:電源管理IC開發工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
XILINXPWR-080 功能描述:電源管理IC開發工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
XILINXPWR-081 功能描述:電源管理IC開發工具 Pwr Mgmt Eval Mod Xilinx RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*