- 您現在的位置：買賣IC網 > Datasheet目錄58 > XIB-R (Digi International/Maxstream)BOARD INTERFACE RS232/485 Datasheet資料下載
參數資料
| 型號： | XIB-R |
| 廠商： | Digi International/Maxstream |
| 文件頁數： | 21/36頁 |
| 文件大小： | 826K |
| 描述： | BOARD INTERFACE RS232/485 |
| 標準包裝： | 1 |
| 附件類型： | 接口板 |
| 適用于相關產品： | XStream 和 Xcite 收音機 |
| 其它名稱： | Q2231853 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
9XCite"燨EM燫F燤odule?燩roduct燤anual爒2.1燵2007.01.04]
2007燤axStream,營nc.
牋牋?1
BT (Guard Time Before) Parameter
<Non-AT Settable Parameter: AT Command Options> BT Parameter is used to set the DI pin silent
time that precedes the command sequence character (CC Parameter). By default, 1 half of a sec-
ond (500 milliseconds) must elapse before entering another character. The AT Command Mode
Sequence used to enter AT Command Mode is as follows:
"No characters sent for 1 millisecond [BT (Guard Time Before) Parameter]
"Send three plus characters "+++" [CC (Command Sequence Character) Parameter]
"No characters sent for 1 millisecond [AT (Guard Time After) Parameter]
All of the values in this sequence can be adjusted. AT Command is used to adjust the period of
silence that precedes the command sequence character.
Parameter Range: 0 - 0xFFFF (x 1 millisecond)
# of bytes returned: 2
Default Parameter Value: 0x1F4 (500 decimal)
Related Commands: AT (Guard Time After), CC (Commands Sequence Character)
CC (Command Sequence Character) Parameter
<Non-AT Settable Parameter: AT Command Options> CC Parameter is used to adjust the com-
mand sequence character used when entering AT Command Mode.
The AT Command Mode Sequence used to enter AT Command Mode is as follows:
"No characters sent for 1 millisecond [BT (Guard Time Before) Parameter]
"Send three plus characters "+++" [CC (Command Sequence Character) Parameter]
"No characters sent for 1 millisecond [AT (Guard Time After) Parameter]
Parameter Range: 0x20 - 0x7F
# of bytes returned: 1
Default Parameter Value: 0x2B (ASCII "+" sign)
Related Parameters: AT (Guard Time After), BT (Guard Time Before)
CD (DO3 Configuration) Command
<AT Command: Serial Interfacing> Used to rede-
fine the RX LED I/O line.
CN (Exit AT Command Mode) Command
<AT Command: AT Command Mode Options> CN Command allows users to explicitly exit AT Com-
mand Mode and return the radio modem into Idle Mode.
AT Command: CN
AT Command: ATCD
Parameter Ranges: 0 - 2
Parameter
Configuration
0
RX LED
1
High
2
Low
Default Parameter Value: 0
Number of bytes returned: 1
相關PDF資料 |
PDF描述 |
|---|---|
| ZMN2400HPDB | BOARD ROUTER DEV ZIGBEE 100MW |
| ZMN24HPDK-B | KIT DEV W/ZIGBEE ZMN2400HP |
| ZNI1000TC | IC TEMP SENSOR NI1000 SOT23-3 |
| 02110102-000 | SNSR TILT RATIO 60DEG 500MA FLNG |
| 1-5209285-2 | FOPC BOA 12DB FC/UPC BP SM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XIB-U | 功能描述:界面模塊 USB interface board 24XStream 9XCite RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度: |
| XIC25040 | 制造商:XIC 功能描述:25040 24HR '6 |
| XILINXPWR-079 | 功能描述:電源管理IC開發工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| XILINXPWR-080 | 功能描述:電源管理IC開發工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| XILINXPWR-081 | 功能描述:電源管理IC開發工具 Pwr Mgmt Eval Mod Xilinx RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。