參數資料
型號： XIB-R
廠商： Digi International/Maxstream
文件頁數： 22/36頁
文件大?。?/td> 826K
描述： BOARD INTERFACE RS232/485
標準包裝： 1
附件類型： 接口板
適用于相關產品： XStream 和 Xcite 收音機
其它名稱： Q2231853
9XCite"燨EM燫F燤odule?燩roduct燤anual爒2.1燵2007.01.04]
2007燤axStream,營nc.
牋牋?2
CS (DO2 Configuration) Command
<AT Command: Serial Interfacing> CS Command
is used to modify the behavior of the CTS
 signal
such that it either provides RS-232 flow control,
enables RS-485 transmission / reception or deter-
mines RS-422 transmit enable. By default, CTS
 
provides RS-232 flow control. CS Parameter must
be adjusted for the modem to operate in RS-485/
422 environments.
CT (Time before Exit AT Command Mode) Parameter
<Non-AT Settable Parameter: AT Command Options> AT Command Mode can be exited manually
using CN (Exit AT Command Mode) Command or, after a given time of inactivity, the modem exits
AT Command Mode on its own and return to Idle Mode. CT Command sets the amount of time
before AT Command Mode is exited automatically. If no characters are received before this time
elapses, the modem will return to Idle Mode.
Parameter Range: 0x02 - 0xFFFF [x 100 ms]
# of bytes returned: 2
Default Parameter Value: 0xC8 (200d (20 decimal seconds))
DB (Receive Signal Strength) Command
<AT Command: Diagnostic> DB Parameter returns the receive signal strength (in decibels) of the
last received packet. This Parameter is useful in determining range characteristics of the XCite
Modules under various conditions.
AT Command: DB
Parameter Range: 0x25 - 0x6A [Read-only]
# of bytes returned: 1
DT (Destination Address) Command
<AT Command: Networking> DT Command is used to set the address of the XCite Radio Modem.
XCite Radio Modems use three network layers - the Vendor Identification Number (ATID), Chan-
nels (ATHP) and Destination Addresses (ATDT).
DT Command assigns an address to a radio modem that enables it to communicate only with radio
modems that have matching addresses. This is similar to interconnecting several PCs under a
common hub. All radio modems that share the same destination address can communicate freely
with each other. Radio Modems in the same network with a different destination address (than that
of the transmitter) will listen to all transmissions to stay synchronized, but will not send any of the
data out their serial ports.
AT Command: DT
Parameter Range: 0 - 0xFFFF
# of bytes returned: 2
Default Parameter Value: 0
Related Commands: ID (Modem ID), HP (Channel), MK (Address Mask)
AT Command: ATCS
Parameter Ranges: 0 - 4
Parameter
Configuration
0
Normal CTS
1
RS-485 enable (low)
2
high
3
RS-485 enable (high)
4
low
Default Parameter Value: 0
Number of bytes returned: 1
相關PDF資料
PDF描述
ZMN2400HPDB BOARD ROUTER DEV ZIGBEE 100MW
ZMN24HPDK-B KIT DEV W/ZIGBEE ZMN2400HP
ZNI1000TC IC TEMP SENSOR NI1000 SOT23-3
02110102-000 SNSR TILT RATIO 60DEG 500MA FLNG
1-5209285-2 FOPC BOA 12DB FC/UPC BP SM
相關代理商/技術參數
參數描述
XIB-U 功能描述:界面模塊 USB interface board 24XStream 9XCite RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度:
XIC25040 制造商:XIC 功能描述:25040 24HR '6
XILINXPWR-079 功能描述:電源管理IC開發工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
XILINXPWR-080 功能描述:電源管理IC開發工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
XILINXPWR-081 功能描述:電源管理IC開發工具 Pwr Mgmt Eval Mod Xilinx RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*