- 您現在的位置：買賣IC網 > Datasheet目錄58 > XIB-R (Digi International/Maxstream)BOARD INTERFACE RS232/485 Datasheet資料下載
參數資料
| 型號： | XIB-R |
| 廠商： | Digi International/Maxstream |
| 文件頁數： | 13/36頁 |
| 文件大小： | 826K |
| 描述： | BOARD INTERFACE RS232/485 |
| 標準包裝： | 1 |
| 附件類型： | 接口板 |
| 適用于相關產品： | XStream 和 Xcite 收音機 |
| 其它名稱： | Q2231853 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
9XCite"燨EM燫F燤odule?燩roduct燤anual爒2.1燵2007.01.04]
2007燤axStream,營nc.
牋牋?3
Serial Port Sleep (SM = 2)
"Wake on serial port activity
Serial Port Sleep is a Sleep Mode setting in which the modem runs in a low power state until data
is detected on the DI pin.
When Serial Port Sleep is enabled, the modem goes into Sleep Mode after a user-defined period of
inactivity (no transmitting or receiving of data). This period of time is determined by ST (Time
before Sleep) Command. The modem returns to Idle Mode once a character is received through
the DI pin.
Cyclic Sleep (SM = 3-8)
Cyclic Sleep is the Sleep Mode setting in which the XCite Module enters into a low power state and
awakens periodically to determine if any transmissions are being sent.
When Cyclic Sleep settings are enabled, the XCite Module goes into Sleep Mode after a user-
defined period of inactivity (no transmission or reception on the RF channel). The user-defined
period is determined by ST Parameter. [See ST (Time before Sleep) Parameter]
While the modem is in a low-power state, CTS
de-asserted (high) to indicate that data should not
be sent to the modem during this time. When the modem awakens to listen for data, CTS
is
asserted and any data received on the DI Pin is transmitted. The PWR pin is also de-asserted (low)
when the modem is in Cyclic Sleep Mode. These pins are asserted each time the modem cycles
into Idle Mode to listen for valid data packets and de-asserts when the modem returns to Sleep
Mode.
The modem remains in Sleep Mode for a user-defined period of time ranging from 0.5 seconds to
16 seconds (SM Parameters 3 through 8). After this interval of time, the modem returns to Idle
Mode and listens for a valid data packet for 100 ms. If the modem does not detect valid data (on
any frequency), the modem returns to Sleep Mode. If valid data is detected, the modem transi-
tions into Receive Mode and receives the incoming packets. The modem then returns to Sleep
Mode after a Period of inactivity that is determined by ST "Time before Sleep" Parameter.
The modem can also be configured to Wake-up from cyclic sleep when the SLEEP pin is de-
asserted (low). To configure a modem to operate in this manner, PW (Pin Wake-up) Command
must be issued. Once the Sleep pin is de-asserted, the modem is forced into Idle Mode and can
begin transmitting or receiving data. It remains active until no data is detected for the period of
time specified by the ST parameter, at which point it resumes its low-power cyclic state.
Note: The cyclic interval time defined by SM (Sleep Mode) Command must be shorter than the interval
time defined by LH ("Wake-up Initializer Timer") Command. For example: If SM=4 (Cyclic 1.0 second
sleep), the LH Parameter should equal 0xB ("1.1" seconds). With these parameters set, there is no risk
of the receiving modem being asleep for the duration of the wake-up initializer transmission. The fol-
lowing section "Cyclic Scanning" explains in further detail the relationship between "Cyclic Sleep" and
"Wake-up Initializer Timer"
Cyclic Scanning. Each RF transmission consists of a wake-up initializer and payload data. The
wake-up initializer contains initialization information and all receiving modems must Wake-up dur-
ing the wake-up initializer portion of data transmission in order to synchronize with the transmitter
and receive the data.
The cyclic interval time defined by the SM (Sleep Mode) command must be shorter than the interval
time defined by LH (Wake-up Initializer Timer) command.
Figure?07. Correct燙onfiguration?LH?燬M):?SPAN class="pst XIB-R_2124010_2">
The爈ength爋f爐he爓akeup爄nitializer爀xceeds爐he爐ime爄nterval爋f燙yclic燬leep.燭he爎eceiver爄s?/DIV>
guaranteed爐o燿etect爐he爓akeup爄nitializer燼nd爎eceive爐he燼ccompanying爌ayload燿ata.
相關PDF資料 |
PDF描述 |
|---|---|
| ZMN2400HPDB | BOARD ROUTER DEV ZIGBEE 100MW |
| ZMN24HPDK-B | KIT DEV W/ZIGBEE ZMN2400HP |
| ZNI1000TC | IC TEMP SENSOR NI1000 SOT23-3 |
| 02110102-000 | SNSR TILT RATIO 60DEG 500MA FLNG |
| 1-5209285-2 | FOPC BOA 12DB FC/UPC BP SM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XIB-U | 功能描述:界面模塊 USB interface board 24XStream 9XCite RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度: |
| XIC25040 | 制造商:XIC 功能描述:25040 24HR '6 |
| XILINXPWR-079 | 功能描述:電源管理IC開發工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| XILINXPWR-080 | 功能描述:電源管理IC開發工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| XILINXPWR-081 | 功能描述:電源管理IC開發工具 Pwr Mgmt Eval Mod Xilinx RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。