參數資料
型號: XC3S250E-5CPG132C
廠商: Xilinx Inc
文件頁數: 194/227頁
文件大?。?/td> 0K
描述: IC FPGA SPARTAN-3E 250K 132CSBGA
標準包裝: 360
系列: Spartan®-3E
LAB/CLB數: 612
邏輯元件/單元數: 5508
RAM 位總計: 221184
輸入/輸出數: 92
門數: 250000
電源電壓: 1.14 V ~ 1.26 V
安裝類型: 表面貼裝
工作溫度: 0°C ~ 85°C
封裝/外殼: 132-TFBGA,CSPBGA
供應商設備封裝: 132-CSPBGA(8x8)
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁當前第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁
Spartan-3E FPGA Family: Functional Description
DS312 (v4.1) July 19, 2013
Product Specification
69
The configuration pins also operate at other voltages by
setting VCCO_2 (and VCCO_1 in BPI mode) to either 3.3V
or 1.8V. The change on the VCCO supply also changes the
I/O characteristics, including the effective IOSTANDARD.
For example, with VCCO = 3.3V, the output characteristics
will be similar to those of LVCMOS33, and the current when
driving High, IOH, increases to approximately 12 to 16 mA,
while the current when driving Low, IOL, remains 8 mA. At
VCCO = 1.8V, the output characteristics will be similar to
those of LVCMOS18, and the current when driving High,
IOH, decreases slightly to approximately 6 to 8 mA. Again,
the current when driving Low, IOL, remains 8 mA. The
output voltages are determined by the VCCO level,
LVCMOS18 for 1.8V, LVCMOS25 for 2.5V, and LVCMOS33
for 3.3V. For more details see UG332.
CCLK Design Considerations
For additional information, refer to the “Configuration Pins
and Behavior during Configuration” chapter in UG332.
The FPGA’s configuration process is controlled by the
CCLK configuration clock. Consequently, signal integrity of
CCLK is important to guarantee successful configuration.
Poor CCLK signal integrity caused by ringing or reflections
might cause double-clocking, causing the configuration
process to fail.
Although the CCLK frequency is relatively low, Spartan-3E
FPGA output edge rates are fast. Therefore, careful
attention must be paid to the CCLK signal integrity on the
printed circuit board. Signal integrity simulation with IBIS is
recommended. For all configuration modes except JTAG,
the signal integrity must be considered at every CCLK trace
destination, including the FPGA’s CCLK pin.
This analysis is especially important when the FPGA
re-uses the CCLK pin as a user-I/O after configuration. In
these cases, there might be unrelated devices attached to
CCLK, which add additional trace length and signal
destinations.
In the Master Serial, SPI, and BPI configuration modes, the
FPGA drives the CCLK pin and CCLK should be treated as
a full bidirectional I/O pin for signal integrity analysis. In BPI
mode, CCLK is only used in multi-FPGA daisy-chains.
The best signal integrity is ensured by following these basic
PCB guidelines:
Route the CCLK signal as a 50
Ω
controlled-impedance transmission line.
Route the CCLK signal without any branching. Do not
use a “star” topology.
Keep stubs, if required, shorter than 10 mm (0.4
inches).
Terminate the end of the CCLK transmission line.
Design Considerations for the HSWAP,
M[2:0], and VS[2:0] Pins
For additional information, refer to the “Configuration Pins
and Behavior during Configuration” chapter in UG332.
Unlike previous Spartan FPGA families, nearly all of the
Spartan-3E dual-purpose configuration pins are available
as full-featured user I/O pins after successful configuration,
when the DONE output goes High.
The HSWAP pin, the mode select pins (M[2:0]), and the
variant-select pins (VS[2:0]) must have valid and stable
logic values at the start of configuration. VS[2:0] are only
used in the SPI configuration mode. The levels on the
M[2:0] pins and VS[2:0] pins are sampled when the INIT_B
pin returns High. See Figure 76 for a timing example.
The HSWAP pin defines whether FPGA user I/O pins have
a pull-up resistor connected to their associated VCCO
supply pin during configuration or not, as shown Table 48.
HSWAP must be valid at the start of configuration and
remain constant throughout the configuration process.
The Configuration section provides detailed schematics for
each configuration mode. The schematics indicate the
required logic values for HSWAP, M[2:0], and VS[2:0] but do
not specify how the application provides the logic Low or
High value. The HSWAP, M[2:0], and VS[2:0] pins can be
either dedicated or reused by the FPGA application.
Dedicating the HSWAP, M[2:0], and VS[2:0] Pins
If the HSWAP, M[2:0], and VS[2:0] pins are not required by
the FPGA design after configuration, simply connect these
pins directly to the VCCO or GND supply rail shown in the
appropriate configuration schematic.
Reusing HSWAP, M[2:0], and VS[2:0] After Config-
uration
To reuse the HSWAP, M[2:0], and VS[2:0] pin after
configuration, use pull-up or pull-down resistors to define
the logic values shown in the appropriate configuration
schematic.
Table 48: HSWAP Behavior
HSWAP
Value
Description
0
Pull-up resistors connect to the associated VCCO
supply for all user-I/O or dual-purpose I/O pins
during configuration. Pull-up resistors are active until
configuration completes.
1
Pull-up resistors disabled during configuration. All
user-I/O or dual-purpose I/O pins are in a
high-impedance state.
相關PDF資料
PDF描述
34VL02T/MS IC EEPROM 2KBIT 400KHZ 8MSOP
XC3S250E-4TQG144I IC FPGA SPARTAN-3E 250K 144-TQFP
34VL02T/MNY IC EEPROM 2KBIT 400KHZ 8TDFN
XC3S250E-4CPG132I IC FPGA SPARTAN-3E 250K 132CSBGA
XC2S50-6FG256C IC FPGA 2.5V C-TEMP 256-FBGA
相關代理商/技術參數
參數描述
XC3S250E-5CPG132C4124 制造商:Xilinx 功能描述:
XC3S250E-5CPG132I 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-3E FPGA Family
XC3S250E-5FG320C 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-3E FPGA Family
XC3S250E-5FG320I 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-3E FPGA Family
XC3S250E-5FG400C 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-3E FPGA Family