- 您現在的位置：買賣IC網 > PDF目錄4292 > XC3S250E-4CPG132I (Xilinx Inc)IC FPGA SPARTAN-3E 250K 132CSBGA PDF資料下載
參數資料
| 型號： | XC3S250E-4CPG132I |
| 廠商： | Xilinx Inc |
| 文件頁數： | 213/227頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC FPGA SPARTAN-3E 250K 132CSBGA |
| 標準包裝： | 360 |
| 系列： | Spartan®-3E |
| LAB/CLB數： | 612 |
| 邏輯元件/單元數： | 5508 |
| RAM 位總計： | 221184 |
| 輸入/輸出數： | 92 |
| 門數： | 250000 |
| 電源電壓： | 1.14 V ~ 1.26 V |
| 安裝類型： | 表面貼裝 |
| 工作溫度： | -40°C ~ 100°C |
| 封裝/外殼： | 132-TFBGA，CSPBGA |
| 供應商設備封裝： | 132-CSPBGA（8x8） |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁當前第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁
Spartan-3E FPGA Family: Functional Description
DS312 (v4.1) July 19, 2013
Product Specification
86
This addressing flexibility allows the FPGA to share the
parallel Flash PROM with an external or embedded
processor. Depending on the specific processor
architecture, the processor boots either from the top or
bottom of memory. The FPGA is flexible and boots from the
opposite end of memory from the processor. Only the
processor or the FPGA can boot at any given time. The
FPGA can configure first, holding the processor in reset or
the processor can boot first, asserting the FPGA’s PROG_B
pin.
The mode select pins, M[2:0], are sampled when the
FPGA’s INIT_B output goes High and must be at defined
logic levels during this time. After configuration, when the
FPGA’s DONE output goes High, the mode pins are
available as full-featured user-I/O pins.
Similarly, the FPGA’s HSWAP pin must be Low to
enable pull-up resistors on all user-I/O pins or High to
disable the pull-up resistors. The HSWAP control must
remain at a constant logic level throughout FPGA
configuration. After configuration, when the FPGA’s DONE
output goes High, the HSWAP pin is available as
full-featured user-I/O pin and is powered by the VCCO_0
supply.
The RDWR_B and CSI_B must be Low throughout the
configuration process. After configuration, these pins also
become user I/O.
In a single-FPGA application, the FPGA’s CSO_B and
CCLK pins are not used but are actively driving during the
configuration process. The BUSY pin is not used but also
actively drives during configuration and is available as a
user I/O after configuration.
After configuration, all of the interface pins except DONE
and PROG_B are available as user I/Os. Furthermore, the
bidirectional SelectMAP configuration peripheral interface
(see Slave Parallel Mode) is available after configuration. To
continue using SelectMAP mode, set the Persist bitstream
generator option to Yes. An external host can then read and
verify configuration data.
The Persist option will maintain A20-A23 as configuration
pins although they are not used in SelectMAP mode.
P
Table 59: Byte-Wide Peripheral Interface (BPI) Connections
Pin Name
FPGA Direction
Description
During Configuration
After Configuration
HSWAP
Input
User I/O Pull-Up Control. When
Low during configuration, enables
pull-up resistors in all I/O pins to
respective I/O bank VCCO input.
0: Pull-ups during configuration
1: No pull-ups
Drive at valid logic level throughout
configuration.
User I/O
M[2:0]
Input
Mode Select. Selects the FPGA
configuration mode. See Design
M2 = 0, M1 = 1. Set M0 = 0 to start
at address 0, increment
addresses. Set M0 = 1 to start at
address 0xFFFFFF and
decrement addresses. Sampled
when INIT_B goes High.
User I/O
CSI_B
Input
Chip Select Input. Active Low.
Must be Low throughout
configuration.
User I/O. If bitstream option
Persist=Yes, becomes
part of SelectMap parallel
peripheral interface.
RDWR_B
Input
Read/Write Control. Active Low
write enable. Read functionality
typically only used after
configuration, if bitstream option
Persist=Yes.
Must be Low throughout
configuration.
User I/O. If bitstream option
Persist=Yes, becomes
part of SelectMap parallel
peripheral interface.
LDC0
Output
PROM Chip Enable
Connect to PROM chip-select
input (CE#). FPGA drives this
signal Low throughout
configuration.
User I/O. If the FPGA does
not access the PROM after
configuration, drive this pin
High to deselect the
PROM. A[23:0], D[7:0],
LDC[2:1], and HDC then
become available as user
I/O.
LDC1
Output
PROM Output Enable
Connect to the PROM
output-enable input (OE#). The
FPGA drives this signal Low
throughout configuration.
User I/O
P
A
相關PDF資料 |
PDF描述 |
|---|---|
| XC2S50-6FG256C | IC FPGA 2.5V C-TEMP 256-FBGA |
| XC2S50-5FG256I | IC FPGA 2.5V I-TEMP 256-FBGA |
| 34VL02/MS | IC EEPROM 2KBIT 400KHZ 8MSOP |
| XC6SLX9-L1CPG196C | IC FPAG SPARTAN 6 9K 196CPGBGA |
| XC6SLX9-2CPG196I | IC FPAG SPARTAN 6 9K 196CPGBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XC3S250E-4FG320C | 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-3E FPGA Family |
| XC3S250E-4FG320I | 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-3E FPGA Family |
| XC3S250E-4FG400C | 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-3E FPGA Family |
| XC3S250E-4FG400I | 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-3E FPGA Family |
| XC3S250E-4FG484C | 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-3E FPGA Family |
發布緊急采購，3分鐘左右您將得到回復。