參數資料
型號： XA-H3
廠商： NXP Semiconductors N.V.
英文描述： CMOS 16-bit highly integrated microcontroller
中文描述： 的CMOS 16位高度集成的微控制器
文件頁數： 23/36頁
文件大?。?/td> 183K
代理商： XA-H3
Philips Semiconductors
Preliminary specification
XA-H3
CMOS 16-bit highly integrated microcontroller
1999 Sep 24
23
Segment Register: Holds A23–A16 (the current segment) of the
24-bit data buffer address.
Buffer Base Register: Holds a pointer (A15–A8) to the lowest byte
in the memory buffer.
Buffer Bound Register: Points to the first out-of-bounds address
above a circular buffer.
Address Pointer Register: Points to a single byte or word in the
data buffer in memory. The 24-bit DMA address is formed by
concatenating the contents of the Segment Register [A23–A16]
with the contents of the Address Pointer Register [A15–A0].
Byte Count Register: Holds the initial number of bytes to be
transferred. In Tx Chaining mode, this register is not used
because the byte count is brought into the byte counter from
buffer headers in memory.
FIFO Control & Status Register: Holds the queuing order and
full/empty status for the Data FIFO Registers.
Data FIFO Registers: A four-byte data FIFO buffer internal to the
DMA channel.
Rx Char Time Out Register (RxCTOR, Rx DMA channels only):
Holds the initial value for an 8-bit character timeout countdown
timer which can generate an interrupt.
Four UARTS
Asynchronous transfers up to
230.4 kbps
5, 6, 7, or 8 data bits per character
1, 1.5, or 2 Stop bits per character
Even or Odd parity generate and check
Parity, Rx Overrun, and Framing Error detection
Break detection
Programmable Baud Rate Generator
Auto Echo and Loopback Modes
I/O Port Output Configuration
Port input/output configurations are the same as standard XA ports:
open drain, quasi-bidirectional, push-pull, and off (off means tri-state
Hi-Z, and allows the pin to be used as an input.
WARNING:
At
power on time, from the time that power coming up is valid, the
P3.2_Timer0_ResetOut pin may be driven low for any period from
zero nanoseconds up to 258 system clocks. This is true
independently of whether ResetIn is active or not.
Power Reduction Modes
The XA-H3 supports Idle and Power Down modes of power
reduction. The idle mode leaves most peripherals running in order to
allow them to activate the processor when an interrupt is generated.
The power down mode stops the oscillator in order to absolutely
minimize power. The processor can be made to exit power down
mode via a reset or one of the external interrupt inputs (INT0 or
INT1). This will occur if the interrupt is enabled and its priority is
higher than that defined by IM3 through IM0. In power down mode,
the power supply voltage may be reduced to the RAM keep-alive
voltage VRAM. This retains the RAM, register, and SFR contents at
the point where power down mode was entered.
WARNING:
V
DD
must be raised to within the operating range before power down
mode is exited.
Interrupts
In the XA architecture, all exceptions, including Reset, are handled in
the same general exception structure. The highest priority exception is
of course Reset, and it is non-maskable. All exceptions are vectored
through the Exception Vector Table in low memory. Coming out of
Reset, these vectors must be stored in non-volatile memory based at
location 000000. Later in the boot sequence, SRAM or other memory
can be mapped into this address space if desired. There is a feature
in the XA-H3 Memory Controller called “Bank Swap” that supports
replacing the ROM vector table and other low memory with RAM. See
the XA-H3 User Manualfor details.
The XA-H3 has a standard XA CPU Interrupt Controller,
implemented with 15 Maskable Event Interrupts. Event Interrupts
are defined as maskable interrupts usually generated by hardware
events. However, in the XA-H3, 4 of the 15 Event Interrupts are
generated by software writing directly to the interrupt flag bit. These
4 interrupts are referred to as High Priority Software Interrupts.
See the IC25 XA Data Handbook for a full explanation of the
exception structure, including event interrupts, of the XA CPU.
Because the High Priority Software Interrupts are specific to the
XA-H3, they are explained in the XA-H3 User Manual
相關PDF資料
PDF描述
XA-H4 Single-chip 16-bit microcontroller
XACA04SPEC0304 CONTROL STATION 4WAY
XACA06SPEC0305 CONTROL STATION 6WAY
XACA215 FERNSTEUEREINHEIT
XALB222 WIPPSCHALTER ZB2 STEUERGEHAEUSE TASTEN 2
相關代理商/技術參數
參數描述
XA-H4 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 16-bit microcontroller
XAI.50V2200 制造商:Xicon Passive Components 功能描述:
XAIR1-3402-101B 制造商:Advantech Co Ltd 功能描述:CARRIER BOARD, AIR PRODUCTS 3402-101B3 - Bulk
XAIR1-3402-CARTON 制造商:Advantech Co Ltd 功能描述:D-AIR01-SOM7562-01 - OUTER CARTON - Bulk
XAITD-100 制造商:RHOMBUS-IND 制造商全稱:Rhombus Industries Inc. 功能描述:XAITD Series FAST / TTL Buffered 10-Tap Delay Modules
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*