- 您現在的位置：買賣IC網 > PDF目錄372537 > X80130 Voltage Supervisor/Sequencer Triple Programmable Time Delay with Local/Remote Voltage Monitors(帶當地/遠程電壓監控功能的電源順序管理器) PDF資料下載
參數資料
| 型號： | X80130 |
| 英文描述： | Voltage Supervisor/Sequencer Triple Programmable Time Delay with Local/Remote Voltage Monitors(帶當地/遠程電壓監控功能的電源順序管理器) |
| 中文描述： | 電壓監控器/可編程序三時滯與本地/遠程電壓監測器（帶當地/遠程電壓監控功能的電源順序管理器） |
| 文件頁數： | 10/19頁 |
| 文件大?。?/td> | 104K |
| 代理商： | X80130 |
REV 1.13 4/30/03
www.xicor.com
Characteristics subject to change without notice
10 of 19
X80130/31/32/33/34 – Preliminary Information
inputs to the X80130. The ViMON inputs monitor the
voltage to make sure it has reached the minimum desired
level. When each voltage monitor determines that its input
is good, a counter starts. After the programmed delay time,
the X80130 sets the ViFAIL signals LOW. The ViFAIL
signals can be wire ORed together and tied to an interrupt
on the microcontroller. Any individual voltage failure can be
viewed in the Fault Detection Register.
In the factory default condition, each voltage monitor is
instructed to go LOW 100ms after the the input voltage
reaches its threshold. However, each ViFAIL delay is
individually selectable as 100ms, 500ms, 1s and 5s. The
delay times are chaged via the SMBus during calibration of
the system.
Figure 7. Example Application of Parallel Power Control.
2)
Power Up of Supplies Via Relay Sequencing Using Voltage
Monitors (see Figure 10 and Figure 9).
Several power supplies and their respective power up start
times can be controlled using the X80130 such that each of
the power supplies will start in a relay sequencing fashion.
In the following example, the 1st supply is allowed to power
up when the input regulated supply reaches an acceptable
threshold. Subsequent supplies power up after the prior
supply has reached its operating voltage. This configuration
ensures that each subsequent power supply turns on after
the preceding supplies voltage output is valid. Again, the
X80130 offers programmable delays for each voltage
monitor and this delay is selectable via the SMBus during
calibration of the system.
Figure 8. Parallel Power Control - Timing
V4GDO
V4MON
V3GDO
V3MON
V1GDO
V1MON
X80130/31/32/33/34
RESET
μC
V
CC1
FPGA
V
CC1
V
CC2
ASIC
V
CC1
V
CC2
RESET
V
CC2
MR
1.2V
2.5V
3.3V
5V
Power
Supplies
IRQ
On/Off
On/Off
On/Off
V1MON
t
DELAY1
V1GDO
Programmable
Delay
Timing
not to scale
100ms
500ms
1 sec
5 secs
V3MON
t
DELAY3
V3GDO
Programmable
Delay
V4MON
t
DELAY4
V4GDO
Programmable
Delay
t
SPOR
Programmable
Delay
RESET
Can Choose Different
Delays for each
Voltage Monitor
相關PDF資料 |
PDF描述 |
|---|---|
| X8037QC | 38-640MHz Low Phase Noise XO |
| X8037QCL | 38-640MHz Low Phase Noise XO |
| X8038QC | 38-640MHz Low Phase Noise XO |
| X8038QCL | 38-640MHz Low Phase Noise XO |
| X8039QC | 38-640MHz Low Phase Noise XO |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X80130Q20I | 制造商:Intersil Corporation 功能描述:Voltage Supervisor/Sequencer Triple Programmable Time Delay with Local/Remote Voltage Monitors |
| X80131 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Voltage Supervisor/Sequencer Triple Programmable Time Delay with Local/Remote Voltage Monitors |
| X80131Q20I | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Voltage Supervisor/Sequencer Triple Programmable Time Delay with Local/Remote Voltage Monitors |
| X80132 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Voltage Supervisor/Sequencer Triple Programmable Time Delay with Local/Remote Voltage Monitors |
| X80132Q20I | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Voltage Supervisor/Sequencer Triple Programmable Time Delay with Local/Remote Voltage Monitors |
發布緊急采購，3分鐘左右您將得到回復。