- 您現在的位置：買賣IC網 > PDF目錄371259 > X4C105V20-VTRIP EEPROM PDF資料下載
參數資料
| 型號： | X4C105V20-VTRIP |
| 元件分類： | EEPROM |
| 英文描述： | EEPROM |
| 中文描述： | EEPROM的 |
| 文件頁數： | 4/19頁 |
| 文件大?。?/td> | 258K |
| 代理商： | X4C105V20-VTRIP |
X4C105
Characteristics subject to change without notice.
4 of 19
REV 1.0.1 6/14/01
www.xicor.com
Serial Start Condition
All commands are preceded by the start condition,
which is a HIGH to LOW transition of SDA when SCL is
HIGH. The device continuously monitors the SDA and
SCL lines for the start condition and will not respond to
any command until this condition has been met. See
Figure 3.
Serial Stop Condition
All communications must be terminated by a stop condi-
tion, which is a LOW to HIGH transition of SDA when
SCL is HIGH. The stop condition is also used to place
the device into the standby power mode after a read
sequence. A stop condition can only be issued after the
transmitting device has released the bus. See Figure 2.
Serial Acknowledge
Acknowledge is a software convention used to indicate
successful data transfer. The transmitting device, either
master or slave, will release the bus after transmitting
eight bits. During the ninth clock cycle, the receiver will
pull the SDA line LOW to acknowledge that it received
the eight bits of data. Refer to Figure 4.
The device will respond with an acknowledge after rec-
ognition of a start condition and if the correct device
identifier and select bits are contained in the slave
address byte. If a write operation is selected, the
device will respond with an acknowledge after the
receipt of each subsequent eight bit word. The device
will acknowledge all incoming data and address bytes,
except for the slave address byte when the device
identifier and/or select bits are incorrect or when the
device is busy, such as during a nonvolatile write.
In the read mode, the device will transmit eight bits of
data, release the SDA line, then monitor the line for an
acknowledge. If an acknowledge is detected and no
stop condition is generated by the master, the device
will continue to transmit data. The device will terminate
further data transmissions if an acknowledge is not
detected. The master must then issue a stop condition
to return the device to standby mode and place the
device into a known state.
Figure 3. Valid Start and Stop Conditions
Figure 4. Acknowledge Response From Receiver
SCL
SDA
Start
Stop
SCL from
Master
Data Output
from Transmitter
Data Output
from Receiver
8
1
9
Start
Acknowledge
相關PDF資料 |
PDF描述 |
|---|---|
| X5001 | Floor Cleaner/Neutralizer; Trade Name, Chemical:Doodleduster RoHS Compliant: NA |
| X5001P | Floor Cleaner/Neutralizer; Dispensing Method:Spray; Trade Name, Chemical:TroubleShooter; Volume:1quart (US) |
| X5001P-4.5A | Multi-Purpose Cleaner; Dispensing Method:Bottle; Trade Name, Chemical:Neutral Quat; Volume:2L RoHS Compliant: NA |
| X5001S8 | Multi-Purpose Cleaner; Dispensing Method:Bottle; Trade Name, Chemical:All Purpose; Volume:1gallon (US) RoHS Compliant: NA |
| X5001S8-2.7 | Cleaner Degreaser; Dispensing Method:Bottle; Trade Name, Chemical:Heavy Duty Degreaser; Volume:1gallon (US) RoHS Compliant: NA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X4C303N1CC | 制造商:SAIA - BURGESS ELECTRONICS INC. 功能描述:Catalogue / X4C303N1CC |
| X4C303N1CCS11 | 制造商:JOHNSON ELECTRIC 功能描述:SWITCH, 3A,125/250VAC, SOLDER 制造商:SAIA - BURGESS ELECTRONICS INC. 功能描述:Catalogue / X4C303N1CCS11 |
| X4C303N8DM | 制造商:SAIA - BURGESS ELECTRONICS INC. 功能描述:Catalogue / X4C303N8DM |
| X4C305N1CC | 制造商:SAIA - BURGESS ELECTRONICS INC. 功能描述:Catalogue / X4C305N1CC |
| X4C308N8DM | 制造商:Johnson Electric / Saia-Burgess 功能描述:Catalogue / X4C308N8DM |
發布緊急采購，3分鐘左右您將得到回復。