- 您現在的位置：買賣IC網 > PDF目錄297797 > X3100V28Z (INTERSIL CORP) 4-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO28 PDF資料下載
參數資料
| 型號： | X3100V28Z |
| 廠商： | INTERSIL CORP |
| 元件分類： | 電源管理 |
| 英文描述： | 4-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO28 |
| 封裝： | ROHS COMPLIANT, PLASTIC, MO-153AE, TSSOP-28 |
| 文件頁數： | 8/41頁 |
| 文件大小： | 561K |
| 代理商： | X3100V28Z |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
16
FN8110.1
January 3, 2008
Over-discharge Protection
If VCELL < VUV, for a time exceeding TUV, the cells are
said to be in a over-discharge state (Figure 4). In this
instance, the X3100 and X3101 automatically switch
the discharge FET OFF (UVP/OCP = Vcc), and then
enter sleep mode.
The over-discharge (under-voltage) value, VUV, can be
selected from the values shown in Table 5 by setting
bits VUV1, VUV0 in the configuration register. These
bits are set using the WCFIG command. Once in the
sleep mode, the following steps must occur before the
X3100 or X3101 allows the battery cells to discharge:
– The X3100 and X3101 must wake from sleep mode
– The charge FET must be switched ON by the micro-
controller (OVP/LMON=VSS), via the control register
– All battery cells must satisfy the condition: VCELL >
VUVR for a time exceeding TUVR.
– The discharge FET must be switched ON by the
microcontroller (UVP/OCP=VSS), via the control reg-
ister (see section “Control Register Functionality” on
The times TUV/TUVR are varied using a capacitor (CUV)
connected between pin UVT and GND (Table 13). The
delay TUV that results from a particular capacitance CUV,
can be approximated by the following linear equation:
TUV (s) ≈ 10 x CUV (F)
TUVR (ms) ≈ 70 x CUV (F)
Sleep Mode
The X3100 or X3101 can enter sleep mode in two
ways:
i) The device enters the over-discharge protection
mode.
ii) The user sends the device into sleep mode using the
control register.
A sleep mode can be induced by the user, by setting
the SLP bit in the control register (Table 13) using the
WCNTR Instruction.
In sleep mode, power to all internal circuitry is
switched off, minimizing the current drawn by the
device to 1A (max). In this state, the discharge FET
and
the
charge
FET
are
switched
OFF
(OVP/LMON=VCC and UVP/OCP=VCC), and the 5VDC
regulated output (VRGO) is 0V. Control of UVP/OCP
and OVP/LMON via bits UVPC and OVPC in the con-
trol register is also prohibited.
The device returns from sleep mode when VCC ≥ VSLR.
(e.g. when the battery terminals are connected to a
battery charger). In this case, the X3100 or the X3101
restores the 5VDC regulated output (section “Voltage
Regulator” on page 22), and communication via the
SPI port resumes.
If the Cell Charge Enable function is enabled when
VCC rises above VSLR, the X3100 and X3101 internally
verifies that the individual battery cell voltages (VCELL)
are larger than the
cell charge enable voltage (VCE)
before allowing the FETs to be turned on. The value
of VCE is selected by using the WCFIG command to
set bits VCE1–VCE0 in the configuration register.
Only if the condition “VCELL > VCE” is satisfied can
the state of charge and discharge FETs be changed
via the control register
. Otherwise, if VCELL < VCE for
any battery cell then both the Charge FET and the dis-
charge
FET
are
OFF
(OVP/LMON=Vcc
and
UVP/OCP=VCC). Thus both charge and discharge of
the battery cells via terminals P+ / P- is prohibited1.
The cell charging threshold function can be switched
ON or OFF by the user, by setting bit SWCEN in the
configuration register (Table 7) using the WCFIG com-
mand. In the case that this cell charge enable function
is switched OFF, then VCE is effectively set to 0V.
Neither the X3100 nor the X3101 enter sleep mode
(automatically or manually, by setting the SLP bit) if
VCC ≥ VSLR. This is to ensure that the device does not
go into a sleep mode while the battery cells are at a
high voltage (e.g. during cell charging).
Table 21. Typical Over-discharge Delay Times
Symbol
Description
CUV
Delay
TUV
Over-discharge
detection delay
0.1F
1.0s (Typ)
TUVR
Over-discharge
release time
0.1F
7ms (Typ)
1. In this case, charging of the battery may resume ONLY if the
cell charge enable function is switched OFF by setting bit
SWCEN = 1 in the configuration register (See Above,
X3100, X3101
相關PDF資料 |
PDF描述 |
|---|---|
| X40420S14-A | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO14 |
| X4163S8Z | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| X4165V8-2.7 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| X4165S8-4.5A | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| X5001S8-1.8 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X3101 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:3 or 4 Cell Li-Ion Battery Protection and Monitor IC |
| X3101PT-V | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:3 or 4 Cell Li-Ion Battery Protection and Monitor IC |
| X3101V28 | 功能描述:IC PROTECT/MONITOR 3CELL 28TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
| X3101V28C7988 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| X3101V28T1 | 功能描述:IC PROTECT/MONITOR 3CELL 28TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
發布緊急采購，3分鐘左右您將得到回復。