參數資料
型號： X3100V28Z
廠商： INTERSIL CORP
元件分類： 電源管理
英文描述： 4-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO28
封裝： ROHS COMPLIANT, PLASTIC, MO-153AE, TSSOP-28
文件頁數： 34/41頁
文件大小： 561K
代理商： X3100V28Z
4
FN8110.1
January 3, 2008
principles of operation
The X3100 and X3101 provide two distinct levels of
functionality and battery cell protection:
First, in Normal mode, the device periodically checks each
cell for an overcharge and overdischarge state, while
continuously watching for a pack over-current condition. A
protection mode violation results from an over-charge, over-
discharge, or overcurrent state. The thresholds for these
states are selected by the user through software. When one
of these conditions occur, a Discharge FET or a Charge FET
or both FETs are turned off to protect the battery pack. In an
over-discharge condition, the X3100 and X3101 devices go
into a low power sleep mode to conserve battery power.
During sleep, the voltage regulator turns off, removing power
from the microcontroller to further reduce pack current.
Second, in Monitor mode, a microcontroller with A/D converter
measures battery cell voltage and pack current via pin AO and
the X3100 or X3101 on-board MUX. The user can thus
implement protection, charge/discharge, cell balancing or gas
gauge software algorithms to suit the specific application and
characteristics of the cells used. While monitoring these
voltages, all protection circuits are on continuously.
In a typical application, the microcontroller is also
programmed to provide an SMBus interface along with the
Smart Battery System interface protocols. These additions
allow an X3100 or X3101 based module to adhere to the
latest industry battery pack standards.
Typical Application Circuit
The X3100 and X3101 have been designed to operate
correctly when used as connected in the Typical Application
Circuit (see Figure 1 on page 5).
The power MOSFET’s Q1 and Q2 are referred to as the
“Discharge FET” and “Charge FET,” respectively. Since
these FETs are p-channel devices, they will be ON when the
gates are at VSS, and OFF when the gates are at VCC. As
their names imply, the discharge FET is used to control cell
discharge, while the charge FET is used to control cell
charge. Diode D1 allows the battery cells to receive charge
even if the Discharge FET is OFF, while diode D2 allows the
cells to discharge even if the charge FET is OFF. D1 and D2
are integral to the Power FETs. It should be noted that the
cells can neither charge nor discharge if both the charge FET
and discharge FET are OFF.
23
OVP/
LMON
Over-charge Voltage Protection output/Load Monitor output. This one pin performs two functions depending upon the
present mode of operation of the X3100 or X3101.
Over-charge Voltage Protection (OVP)
This pin controls the switching of the battery pack charge FET. This power FET is a P-channel device. As such, cell charge is
possible when OVP/LMON=VSS, and cell charge is prohibited when OVP/LMO = VCC. In this configuration the X3100 and
X3101 turn off the charge voltage when the cells reach the over-charge limit. This prevents damage to the battery cells due to
the application of charging voltage for an extended period of time (see section “Over-charge Protection” on page 14).
Load Monitor (LMON)
In Over-current Protection mode, a small test current (7.5A typ.) is passed out of this pin to sense the load resistance. The
measured load resistance determines whether or not the X3100 or X3101 returns from an over-current protection mode (see
24
UVP/
OCP
Over-discharge protection output/Over-current protection output. Pin UVP/OCP controls the battery cell discharge via
an external power FET. This P-channel FET allows cell discharge when UVP/OCP=Vss, and prevents cell discharge when
UVP/OCP=Vcc. The X3100 and X3101 turn the external power FET off when the X3100 or X3101 detects either:
Over-discharge Protection (UVP)
In this case, pin 24 is referred to as “Over-discharge (Under-Voltage) protection (UVP)” (see section “Over-discharge
Protection” on page 16). UVP/OCP turns off the FET to prevent damage to the battery cells by being discharged to
excessively low voltages.
Over-current protection (OCP)
In this case, pin 24 is referred to as “Over-current protection (OCP)” (see section “Over-Current Protection” on page 19).
UVP/OCP turns off the FET to prevent damage to the battery pack caused by excessive current drain (e.g. as in the case of
a surge current resulting from a stalled disk drive).
25
RGO
Voltage regulator output pin. This pin is an input that connects to the collector of an external PNP transistor. The voltage
at this pin is the regulated output voltage, but it also provides the feedback voltage for the regulator and the operating voltage
for the device.
26
RGC
Voltage regulator control pin. This pin connects to the base of an external PNP transistor and controls the transistor turn on.
27
RGP
Voltage regulator protection pin. This pin is an input that connects to the emitter of an external PNP transistor and an
external current limit resistor and provides a current limit voltage.
28
VCC
Power supply. This pin is provides the voltage for FET control, regulator operation, and wake-up
circuits.
Pin Descriptions (Continued)
PIN
NUMBER PIN NAME
BRIEF DESCRIPTION
X3100, X3101
相關PDF資料
PDF描述
X40420S14-A 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO14
X4163S8Z 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8
X4165V8-2.7 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8
X4165S8-4.5A 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8
X5001S8-1.8 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8
相關代理商/技術參數
參數描述
X3101 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:3 or 4 Cell Li-Ion Battery Protection and Monitor IC
X3101PT-V 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:3 or 4 Cell Li-Ion Battery Protection and Monitor IC
X3101V28 功能描述:IC PROTECT/MONITOR 3CELL 28TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT
X3101V28C7988 制造商:Rochester Electronics LLC 功能描述:- Bulk
X3101V28T1 功能描述:IC PROTECT/MONITOR 3CELL 28TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*