- 您現在的位置：買賣IC網 > PDF目錄372527 > X1209 Real Time Clock/Calendar with Event/Timestamp Detection & Alarms(帶有事件/時間標記檢測與報警功能的實時時鐘/日歷) PDF資料下載
參數資料
| 型號： | X1209 |
| 英文描述： | Real Time Clock/Calendar with Event/Timestamp Detection & Alarms(帶有事件/時間標記檢測與報警功能的實時時鐘/日歷) |
| 中文描述： | 實時時鐘/日歷的事件/時間戳檢測 |
| 文件頁數： | 23/27頁 |
| 文件大?。?/td> | 511K |
| 代理商： | X1209 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁
23 of 27
REV 3.0 2/11/04
www.xicor.com
Preliminary Information
X1209
Random Read
Random read operations allow the master to access
any location in the X1209. Prior to issuing the Slave
Address Byte with the R/W bit set to zero, the master
must first perform a “dummy” write operation.
The master issues the start condition and the slave
address byte, receives an acknowledge, then issues
the word address bytes. After acknowledging receipt of
each word address byte, the master immediately
issues another start condition and the slave address
byte with the R/W bit set to one. This is followed by an
acknowledge from the device and then by the eight bit
data word. The master terminates the read operation
by not responding with an acknowledge and then issu-
ing a stop condition. Refer to Figure 10 for the address,
acknowledge, and data transfer sequence.
In a similar operation called “Set Current Address,” the
device sets the address if a stop is issued instead of
the second start shown in Figure 10. The X1209 then
goes into standby mode after the stop and all bus
activity will be ignored until a start is detected. This
operation loads the new address into the address
counter. The next Current Address Read operation will
read from the newly loaded address. This operation
could be useful if the master knows the next address it
needs to read, but is not ready for the data.
Sequential Read
Sequential reads can be initiated as either a current
address read or random address read. The first data
byte is transmitted as with the other modes; however,
the master now responds with an acknowledge, indi-
cating it requires additional data. The device continues
to output data for each acknowledge received. The mas-
ter terminates the read operation by not responding with
an acknowledge and then issuing a stop condition.
The data output is sequential, with the data from
address n followed by the data from address n + 1.
Refer to Figure 11 for the acknowledge and data trans-
fer sequence.
Figure 10. Random Address Read Sequence
Figure 11. Sequential Read Sequence
0
Slave
Address
Word
Address 1
A
C
K
A
C
K
S
t
a
r
t
S
t
o
p
Slave
Address
Data
A
C
K
1
S
t
a
r
t
SDA Bus
Signals from
the Slave
Signals from
the Master
A
C
K
Word
Address 0
1
1
1
1
1
1
1
1
0 0 0 0 0 0 0
1
0
1
1
0
1
Data
(2)
S
t
o
p
Slave
Address
Data
(n)
A
C
K
A
C
K
SDA Bus
Signals from
the Slave
Signals from
the Master
1
Data
(n-1)
A
C
K
A
C
K
(n is any integer greater than 1)
Data
(1)
相關PDF資料 |
PDF描述 |
|---|---|
| X1226(中文) | Real Time Clock/Calendar with Output Frequency and EEPROM(實時時鐘/日歷，帶輸出頻率和EEPROM) |
| X1226 | Real Time Clock/Calendar with EEPROM |
| X1226S8 | Real Time Clock/Calendar with EEPROM |
| X1226S8I | Real Time Clock/Calendar with EEPROM |
| X1226V8 | Real Time Clock/Calendar with EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X1210MKX7R8BB564 | 制造商:Yageo / Phycomp 功能描述:0.56uF 25V SM CAP-X2Y FILTER 1210 X7R 20% Ni Barr w/100% Tin - free partial T/R at 500. |
| X121198-ISD | 制造商:Honeywell Sensing and Control 功能描述:RESISTIVE & OPTICAL |
| X-1214-1 | 制造商:Pulse Electronics Corporation 功能描述:DATA BUS - Rail/Tube |
| X-1215-1 | 制造商:Pulse Electronics Corporation 功能描述:DATA BUS - Rail/Tube |
| X121770-ISD | 制造商:Honeywell Sensing and Control 功能描述:RESISTIVE & OPTICAL |
發(fā)布緊急采購，3分鐘左右您將得到回復。