參數資料
型號： W25P20-VSNI-G
廠商： WINBOND ELECTRONICS CORP
元件分類： PROM
英文描述： 2M X 1 FLASH 2.7V PROM, PDSO8
封裝： 0.150 INCH, GREEN, PLASTIC, SOIC-8
文件頁數： 34/35頁
文件大小： 1405K
代理商： W25P20-VSNI-G
W25P10, W25P20 AND W25P40
- 8 -
6.
FUNCTIONAL DESCRIPTION
6.1
SPI OPERATIONS
6.1.1
SPI Modes
The W25P10/20/40 is accessed through an SPI compatible bus consisting of four signals: Serial Clock
(CLK), Chip Select (/CS), Serial Data Input (DI) and Serial Data Output (DO). Both SPI bus operation
Modes 0 (0,0) and 3 (1,1) are supported. The primary difference between Mode 0 and Mode 3
concerns the normal state of the CLK signal when the SPI bus master is in standby and data is not
being transferred to the Serial Flash. For Mode 0 the CLK signal is normally low. For Mode 3 the CLK
signal is normally high. In either case data input on the DI pin is sampled on the rising edge of the
CLK. Data output on the DO pin is clocked out on the falling edge of CLK.
6.1.2
Hold Function
The /HOLD signal allows the W25P10/20/40 operation to be paused while it is actively selected (when
/CS is low). The /HOLD function may be useful in cases where the SPI data and clock signals are
shared with other devices. For example, consider if the page buffer was only partially written when a
priority interrupt requires use of the SPI bus. In this case the /HOLD function can save the state of the
instruction and the data in the buffer so programming can resume where it left off once the bus is
available again.
To initiate a /HOLD condition, the device must be selected with /CS low. A /HOLD condition will
activate on the falling edge of the /HOLD signal if the CLK signal is already low. If the CLK is not
already low the /HOLD condition will activate after the next falling edge of CLK. The /HOLD condition
will terminate on the rising edge of the /HOLD signal if the CLK signal is already low. If the CLK is not
already low the /HOLD condition will terminate after the next falling edge of CLK.
During a /HOLD condition, the Serial Data Output (DO) is high impedance, and Serial Data Input (DI)
and Serial Clock (CLK) are ignored. The Chip Select (/CS) signal should be kept active (low) for the
full duration of the /HOLD operation to avoid resetting the internal logic state of the device.
6.2
WRITE PROTECTION
Applications that use non-volatile memory must take into consideration the possibility of noise and
other adverse system conditions that may compromise data integrity. To address this concern the
W25P10/20/40 provides several means to protect data from inadvertent writes.
6.2.1
Write Protect Features
Device resets when VCC is below threshold.
Time delay write disable after Power-up.
Write enable/disable instructions.
Automatic write disable after program and erase.
Software write protection using Status Register.
Hardware write protection using Status Register and /WP pin.
Write Protection using Power-down instruction.
相關PDF資料
PDF描述
W25Q128BVFAP 128M X 1 SPI BUS SERIAL EEPROM, PDSO16
W25Q128BVEIP 128M X 1 SPI BUS SERIAL EEPROM, PDSO8
W25Q128BVFIP 128M X 1 SPI BUS SERIAL EEPROM, PDSO16
W25Q16CLSFIP 16M X 1 SPI BUS SERIAL EEPROM, PDSO16
W25Q16CLDAIG 16M X 1 SPI BUS SERIAL EEPROM, PDIP8
相關代理商/技術參數
參數描述
W25P20VSNIG T&R 功能描述:IC FLASH 2MBIT 40MHZ 8SOIC RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:SpiFlash® 標準包裝:1,000 系列:- 格式 - 存儲器:RAM 存儲器類型:移動 SDRAM 存儲容量:256M（8Mx32） 速度:133MHz 接口:并聯 電源電壓:1.7 V ~ 1.95 V 工作溫度:-40°C ~ 85°C 封裝/外殼:90-VFBGA 供應商設備封裝:90-VFBGA（8x13） 包裝:帶卷 (TR) 其它名稱:557-1327-2
W25P222A 制造商:WINBOND 制造商全稱:Winbond 功能描述:64K X 32 BURST PIPELINED HIGH-SPEED CMOS STATIC RAM
W25P222A-4 制造商:WINBOND 制造商全稱:Winbond 功能描述:64K X 32 BURST PIPELINED HIGH-SPEED CMOS STATIC RAM
W25P222A-4A 制造商:WINBOND 制造商全稱:Winbond 功能描述:64K X 32 BURST PIPELINED HIGH-SPEED CMOS STATIC RAM
W25P222AD-4 制造商:WINBOND 制造商全稱:Winbond 功能描述:64K X 32 BURST PIPELINED HIGH-SPEED CMOS STATIC RAM
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*