參數資料
型號： TPS56100PWPR
元件分類： 基準電壓源/電流源
英文描述： Voltage-Mode SMPS Controller
中文描述： 電壓模式開關電源控制器
文件頁數： 26/34頁
文件大小： 811K
代理商： TPS56100PWPR
TPS56302
DUAL-OUTPUT LOW-INPUT-VOLTAGE
DSP POWER SUPPLY CONTROLLER WITH SEQUENCING
SLVS289A
–
MARCH 2000
–
REVISED OCTOBER 2000
26
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
output capacitor RMS current
Assuming the inductor ripple current totally goes through the output capacitor to ground, the RMS current in the
output capacitor can be calculated as:
12
I
I
=
O(rms)
Where I
O(rms)
is the maximum RMS current in the output capacitor (A);
I is the peak-to-peak inductor ripple
current (A).
Example:
I = 1 A, so I
O(rms)
= 0.29 A
input capacitor RMS current
The input capacitor RMS current is important for input capacitor design. Assuming the input ripple current totally
goes into the input capacitor to the power ground, the RMS current in the input capacitor can be calculated as:
II(rms)
IO
2
D
(1
D)
1
12
D
Iripple
2
Where I
I(rms)
is the input RMS current in the input capacitor (A); I
O
is the output current (A); I
ripple
is the
peak-to-peak output inductor ripple current; D is the duty cycle. From the equation, it can be seen that the
highest input RMS current usually occurs at the lowest input voltage, so it is the worst case design for input
capacitor ripple current.
Example:
I
O
= 5 A; D = 0.36; I
ripple
= 1 A,
Then, I
I(rms)
= 2.46 A
layout and component value consideration
Good power supply results will only occur when care is given to proper design and layout. Layout and
component value will affect noise pickup and generation and can cause a good design to perform with less than
expected results. With a range of current from milliamps to tens or even hundreds of amps, good power supply
layout and component selection, especially for a fast ripple controller, is much more difficult than most general
PCB design. The general design should proceed from the switching node to the output, then back to the driver
section, and, finally, to placing the low-level components. In the following list are several specific points to
consider before layout and component selection for TPS56302:
1.
All sensitive analog components should be referenced to ANAGND. These include components connected
to SLOWST, DROOP, IOUT, OCP, VSENSE, VREFB, VHYST, BIAS, and LOSENSE/LOHIB.
2.
The input voltage range for TPS56302 is low from 2.8-V to 5.5-V, so it has a voltage tripler (charge pump)
inside to deliver proper voltage for internal circuitry. To avoid any possible noise coupling, a low ESR
capacitor on V
CC
is recommended.
For the same reason in Item 2, the ANAGND and DRVGND should be connected as close as possible to
the IC.
3.
4.
The bypass capacitor should be placed close to the TPS56302.
相關PDF資料
PDF描述
TPS5615CPWPR Voltage-Mode SMPS Controller
TPS5618CPWPR Voltage-Mode SMPS Controller
TPS5625CPWPR Voltage-Mode SMPS Controller
TPS60100PWPR Analog IC
TPS60101PWPR Analog IC
相關代理商/技術參數
參數描述
TPS56100PWPRG4 功能描述:DC/DC 開關控制器 5B Programmable Synch Buck Cntrlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
TPS561201DDCR 功能描述:AUGUSTA NEXT 1A 制造商:texas instruments 系列:* 零件狀態:在售 標準包裝:1
TPS561201DDCT 功能描述:4.5V TO 17V INPUT, 1A SYNCHRONOU 制造商:texas instruments 系列:SWIFT?? 包裝:剪切帶（CT） 零件狀態:在售 功能:降壓 輸出配置:正 拓撲:降壓 輸出類型:可調式 輸出數:1 電壓 - 輸入（最小值）:4.5V 電壓 - 輸入（最大值）:17V 電壓 - 輸出（最小值/固定）:0.76V 電壓 - 輸出（最大值）:7V 電流 - 輸出:1A 頻率 - 開關:580kHz 同步整流器:是 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商器件封裝:SOT-23-6 標準包裝:1
TPS561201EVM-896 功能描述:EVAIL MOD 制造商:texas instruments 系列:* 零件狀態:在售 標準包裝:1
TPS561208DDCR 功能描述:AUGUSTANEXT 1A 制造商:texas instruments 系列:* 零件狀態:在售 標準包裝:1
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*