參數資料
型號： TMP96C141AF
廠商： Toshiba Corporation
英文描述： High Speed Advanced CMOS 16-bit Microcontroller For Controlling Medium to Large-Scale Equipment(用于中等到大型設備控制，高速、先進的 CMOS 16位微控制器)
中文描述： 采用先進的CMOS高速16位微控制器控制中的大型設備（用于中等到大型設備控制，高速，先進的的CMOS 16位微控制器）
文件頁數： 143/178頁
文件大?。?/td> 5667K
代理商： TMP96C141AF
TOSHIBA CORPORATION
143
TMP96C141AF
3.12.1 Operation
(1)
Analog Reference Voltage
High analog reference voltage is applied to the VREF
pin, and low analog reference voltage is applied to
AGND pin.
The reference voltage between VREG and AGND is
divided by 1024 using ladder resistance, and com-
pared with the analog input voltage for A/D conversion.
(2)
Analog Input Channels
Analog input channel is selected by ADMOD <ADCH1,
0>. However, which channel to select depends on the
operation mode of the A/D converter.
In fixed analog input mode, one channel is selected by
ADMOD <ADCH1, 0> among four pins: AN0 to AN3.
In analog input channel scan mode, the number of
channels to be scanned from AN0 is specified by
ADMOD <ADCH1, 0>, such as AN0
AN1
→
AN2, and AN0
→
AN1
When reset, A/D conversion channel register will be ini-
tialized to ADMOD <ADCH1, 0> = 00, so that AN0 pin
will be selected.
The pins which are not used as analog input channel
can be used as ordinary input port P5.
→
AN1, AN0
AN2
→
AN3.
→
→
(3)
Starting A/D Conversion
A/D conversion starts when A/D conversion register
ADMOD <ADS> is written “1". When A/D conversion
starts, A/D conversion busy flag ADMOD <ADBF>
which indicates “A/D conversion is in progress” will be
set to “1".
(4)
A/D Conversion Mode
Both fixed A/D conversion channel mode and A/D
conversion channel scan mode have two conversion
modes, i.e., single and repeat conversion modes.
In fixed channel repeat mode, conversion of specified
one channel is executed repeatedly.
In scan repeat mode, scanning from AN0,
executed repeatedly.
A/D conversion mode is selected by ADMOD <REPET,
SCAN>.
…
→
AN3 is
(5)
A/D Conversion Speed Selection
There are two A/D conversion speed modes: high
speed mode and low speed mode. The selection is
executed by ADMOD <ADCS> register.
When reset, ADMOD <ADCS> will be initialized to “0,”
so that high speed conversion mode will be selected.
(6)
A/D Conversion End and Interrupt
A/D conversion single mode
ADMOD <EOCF> for A/D conversion end will be
set to “1,” ADMOD <ADBF> flag will be reset to “0,”
and INTAD interrupt will be enabled when A/D conver-
sion of specified channel ends in fixed conversion
channel mode or when A/D conversion of the last
channel ends in channel scan mode.
A/D conversion repeat mode
For both fixed conversion channel mode and con-
version channel scan mode, INTAD should be disabled
when in repeat mode. Always set the INTE0AD at
“000,” that disables the interrupt request.
Write “0” to ADMOD <REPET> to end the repeat
mode. Then, the repeat mode will be exited as soon as
the conversion in progress is completed.
(7)
Storing the A/D Conversion Result
The results of A/D conversion are stored in ADREG0 to
ADREG3 registers for each channel. In repeat mode,
the registers are updated whenever conversion ends.
ADREG0 to ADREG3 are read-only registers.
(8)
Reading the A/D Conversion Result
The results of A/D conversion are stored in ADREG0 to
ADREG3 registers. When the contents of one of
ADREG0 to ADREG3 registers are read, ADMOD
<EOCF> will be cleared to “0".
Setting example:
When the analog input voltage of the
AN3 pin is A/D converted and the
result is stored in the memory
address FF10H by A/D interrupt
INTAD routine.
相關PDF資料
PDF描述
TMP96CM40F High Speed Advanced CMOS 16-bit Microcontroller With Bulit-in 32K Byte OTP ROM For Controlling Medium to Large-Scale Equipment(用于中等到大型設備控制，高速、先進的 CMOS 16位微控制器，芯片內置32K字節可一次編程ROM)
TMPA8700PSF CMOS 8-bit one-time PROM Microcontroller(CMOS OTP型EPROM 8位微控制器)
TMPA8700PSN CMOS 8-bit one-time PROM Microcontroller(CMOS OTP型EPROM 8位微控制器)
TMPR3904AF 32 Bit TX39 Family System RISC Microprocessor(32位TX39系列簡化指令系統計算機微處理器)
TMPR3907F 32 Bit TX39 Family System RISC Microprocessor(32位TX39系列簡化指令系統計算機微處理器)
相關代理商/技術參數
參數描述
TMP96C141BF 功能描述:16位微控制器 - MCU ROMLESS TLCS 900 w/ 1K RAM RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
TMP96C141BFG 功能描述:16位微控制器 - MCU 900 Romless MCU 1K RAM RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
TMP96CM40F 制造商:Toshiba America Electronic Components 功能描述:TLCS900 M/ROM, 32K ROM , 1K RAM - Tape and Reel
TMP96PM40F 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Quality And Reliability Assurance / Handling Precautions
TMP96PM40F(Z) 功能描述:16位微控制器 - MCU 32K ROM OTP 1K RAM RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*