- 您現在的位置：買賣IC網 > PDF目錄382581 > TDA8030 (NXP Semiconductors N.V.) USB smart card reader (OTP or ROM) PDF資料下載
參數資料
| 型號： | TDA8030 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | USB smart card reader (OTP or ROM) |
| 中文描述： | USB智能卡閱讀器（OTP或光盤） |
| 文件頁數： | 44/57頁 |
| 文件大小： | 228K |
| 代理商： | TDA8030 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁當前第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
2003 Jul 04
44
Philips Semiconductors
Product specification
USB smart card reader (OTP or ROM)
TDA8030; TDA8031
8.5.8
A
NALOG INTERFACE
The transceiver interfaces directly to the USB cables
through termination resistors. They are able to transmit
and receive serial data at full speed (12 Mbits/s).
A 1.5 k
pull-up resistor is integrated between pins D+
and V
DDD
and is connected by software by the
microcontroller; in case a
±
5% resistor is preferred, it can
be externally connected between pins DELATT and D+
(DELATT is also controlled by software and is floating
when OFF, or connected to V
DDD
when ON).
8.5.9
S
USPEND MODE
When the USB interface enters Suspend mode, the
software should set the microcontroller in power-down
mode in order to respect the suspend current condition.
The following sequence should be executed:
1.
When the device enters the Suspend mode, it
generates an interrupt on pin INT1
2.
The software should set USB_INT_MASK to logic 1
3.
Then it should wait until CLK_EN_N is HIGH before
entering power-down mode.
When the device detects an activity on the bus, it resets
CLK_EN_N to logic 0 and generates an interrupt on pin
INT1. When leaving the Suspend mode, the following
sequence should be executed:
1.
The software should read the DEVICE_STATUS to
enable the interrupt to be cleared
2.
Reset USB_INT_MASK to logic 0.
相關PDF資料 |
PDF描述 |
|---|---|
| TDA8030HL | USB smart card reader (OTP or ROM) |
| TDA8031 | USB smart card reader (OTP or ROM) |
| TDA8031HL | USB smart card reader (OTP or ROM) |
| TDA8302 | SMALL SIGNAL COMBINATION IC FOR COLOUR TV |
| TDA8931 | Power comparator 1 X 20 W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA8030HL | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:USB smart card reader (OTP or ROM) |
| TDA8031 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:USB smart card reader (OTP or ROM) |
| TDA8031HL | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:USB smart card reader (OTP or ROM) |
| TDA8034AT | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Smart card interface |
| TDA8034AT/C1 | 制造商:NXP Semiconductors 功能描述:Cut Tape |
發布緊急采購，3分鐘左右您將得到回復。