- 您現在的位置：買賣IC網 > PDF目錄382581 > TDA8030 (NXP Semiconductors N.V.) USB smart card reader (OTP or ROM) PDF資料下載
參數資料
| 型號： | TDA8030 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | USB smart card reader (OTP or ROM) |
| 中文描述： | USB智能卡閱讀器（OTP或光盤） |
| 文件頁數： | 25/57頁 |
| 文件大?。?/td> | 228K |
| 代理商： | TDA8030 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
2003 Jul 04
25
Philips Semiconductors
Product specification
USB smart card reader (OTP or ROM)
TDA8030; TDA8031
Table 22
Description of the UCR1 bits
8.1.5.6
Clock configuration register
The Clock Configuration Register (CCR) defines the clock to the card and the clock to the ISO UART. If bit CKU in the
Prescaler Register (UCR2) of the card is set, then the ISO UART is clocked at twice the frequency to the card, this allows
higher baud rates to be reached than foreseen in the ISO7816 norm.
Table 23
Clock configuration register (address 01H; read and write); note 1
Note
1.
All bits are cleared after reset.
BIT
SYMBOL
FIP
DESCRIPTION
7
6
not used
Force Inverse Parity: If FIP = 1, then the UART will NAK a correct received character
and will transmit characters with wrong parity bit.
Bit FC is a test bit and must be left at logic 0.
Protocol: Bit PROT = 1 if the protocol type is asynchronous T = 1. If PROT = 0, the
protocol is T = 0.
Transmit/Receive: Bit T/R is set by software for transmission mode. A change from
0 to 1 will set bit TBE in the USR. T/R is automatically reset by hardware if LCT has
been used before transmitting the last character.
Last Character to Transmit: Bit LCT is set by software before writing the last character
to transmit into the UTR. It allows automatic change to reception mode when reset by
hardware at the end of a successful transmission (11 +
28
31
or
28
32
ETU in T = 0 and
10 +
28
31
or
28
32
ETU in T = 1). When LCT is being reset, the bit T/R is also reset and
the UART is then ready for receiving a character.
Start Session: Bit SS is set by software before ATR for automatic convention detection
and early answer detection. It is automatically reset by hardware at 10.5 ETU after
reception of the initial character.
Convention: Bit CONV = 1 if the convention is direct. CONV is either automatically
written to by hardware, according to the convention detected during ATR, or by software
if bit AUTOCONV is set.
5
4
FC
PROT
3
T/R
2
LCT
1
SS
0
CONV
7
6
5
4
3
2
1
0
SHL
CST
SC
AC2
AC1
AC0
相關PDF資料 |
PDF描述 |
|---|---|
| TDA8030HL | USB smart card reader (OTP or ROM) |
| TDA8031 | USB smart card reader (OTP or ROM) |
| TDA8031HL | USB smart card reader (OTP or ROM) |
| TDA8302 | SMALL SIGNAL COMBINATION IC FOR COLOUR TV |
| TDA8931 | Power comparator 1 X 20 W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA8030HL | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:USB smart card reader (OTP or ROM) |
| TDA8031 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:USB smart card reader (OTP or ROM) |
| TDA8031HL | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:USB smart card reader (OTP or ROM) |
| TDA8034AT | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Smart card interface |
| TDA8034AT/C1 | 制造商:NXP Semiconductors 功能描述:Cut Tape |
發布緊急采購，3分鐘左右您將得到回復。