- 您現在的位置：買賣IC網 > PDF目錄382581 > TDA8030 (NXP Semiconductors N.V.) USB smart card reader (OTP or ROM) PDF資料下載
參數資料
| 型號： | TDA8030 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | USB smart card reader (OTP or ROM) |
| 中文描述： | USB智能卡閱讀器（OTP或光盤） |
| 文件頁數： | 42/57頁 |
| 文件大?。?/td> | 228K |
| 代理商： | TDA8030 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁當前第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
2003 Jul 04
42
Philips Semiconductors
Product specification
USB smart card reader (OTP or ROM)
TDA8030; TDA8031
Table 42
Power-on value for Select end-point
Table 43
Description of the Power-on value for Select end-point bits
Table 44
Power-on value for Set end-point status; notes 1 and 2
Notes
1.
2.
X = dont care.
def means that the bit can be set if the end-point is of the specified type.
FUNCTION
7
6
5
4
0
3
0
2
0
1
0
0
Full or empty
Stall
Set-up
Packet overwritten
Sent NAK
Reserved
0
FUNCTION
DESCRIPTION
Full or empty
If set to logic 1, the buffer of the selected end-point is full.
In the event of an output end-point, this bit is cleared by executing the Clear Buffer command, if
the buffer was not overwritten.
In the event of an input end-point, this bit is set by the Validate Buffer command.
If set to logic 1, the selected end-point is stalled.
If set to logic 1, the last received packet for the selected end-point was a set-up packet. The
value of this bit is updated after each successfully received packet (i.e. an ACKED package on
that particular end-point).
If set to logic 1, the previously received packet was overwritten by a set-up packet. The value of
this bit is cleared by the Select End-point command.
If set to logic 1, the device has sent a NAK. If the host sends an output packet to a filled output
buffer, the device returns a NAK. If the host sends an input token to an empty input buffer, the
device returns a NAK.
This bit is set when a NAK is sent and the Interrupt On Nak feature is enabled.
This bit is reset after the device has sent an ACK after an output packet or when the device has
seen an ACK after sending an input packet. It is only defined for the 2 physical control
end-points.
Stall
Set-up
Packet overwritten
Sent NAK
FUNCTION
7
6
0
5
0
4
3
2
1
0
CTRL EP
GEN IN/OUT
GEN IN
Stall
Disable
Rate feedback
mode
Interrupt unmasked
Conditional stall
0
def
X
X
def
def
def
def
def
def
0
0
X
X
X
X
X
def
相關PDF資料 |
PDF描述 |
|---|---|
| TDA8030HL | USB smart card reader (OTP or ROM) |
| TDA8031 | USB smart card reader (OTP or ROM) |
| TDA8031HL | USB smart card reader (OTP or ROM) |
| TDA8302 | SMALL SIGNAL COMBINATION IC FOR COLOUR TV |
| TDA8931 | Power comparator 1 X 20 W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA8030HL | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:USB smart card reader (OTP or ROM) |
| TDA8031 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:USB smart card reader (OTP or ROM) |
| TDA8031HL | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:USB smart card reader (OTP or ROM) |
| TDA8034AT | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Smart card interface |
| TDA8034AT/C1 | 制造商:NXP Semiconductors 功能描述:Cut Tape |
發布緊急采購，3分鐘左右您將得到回復。