參數資料
型號： TDA8030
廠商： NXP Semiconductors N.V.
英文描述： USB smart card reader (OTP or ROM)
中文描述： USB智能卡閱讀器（OTP或光盤）
文件頁數： 31/57頁
文件大小： 228K
代理商： TDA8030
2003 Jul 04
31
Philips Semiconductors
Product specification
USB smart card reader (OTP or ROM)
TDA8030; TDA8031
8.3
ISO7816 SECURITY
8.3.1
I
NTRODUCTION
Thecorrectsequenceduringactivationanddeactivationof
thecardsisensuredthroughaspecificsequencer,clocked
by a division ratio of the internal oscillator.
Activation(STARTbitHIGHinthePowerControlRegister)
is only possible if the card is present (PRES active HIGH)
and if the supply voltage is correct (supervisor not active).
The presence of the card is signalled to the microcontroller
by the Hardware Status Register (HSR).
Bit PRL in the HSR is set if the card is present. Bit PRL in
the HSR is set if bit PRL has toggled.
During a session, the sequencer performs an automatic
emergency deactivation on the card in the event of card
take off, a short-circuit, a supply drop-out or overheating.
When the HSR register is updated and the INT0 line goes
LOW, the microcontroller will also be updated.
8.3.2
P
ROTECTIONS AND LIMITATIONS
TheTDA8030;TDA8031featuresthefollowingprotections
and limitations:
1.
I
CC
limited to 100 mA, deactivated when this limit is
reached
2.
Current to and from RST is limited to 20 mA,
deactivated when this limit is reached
3.
Deactivation when the temperature of the die exceeds
150
°
C
4.
Current to and from the I/O is limited to 10 mA
5.
Current to and from pin CLK is limited to 70 mA (not in
current reduction modes, when clock is stopped)
6.
ESD protection on all cards contacts + PRES at
6 kV (min.), thus no need of extra components for
protection against ESD flash caused by a charged
card being introduced in the slot
7.
Short-circuit between any cards contacts can last any
duration without any damage.
8.3.3
A
CTIVATION SEQUENCE
When the card is inactive, V
CC
, CLK, RST, I/O, C4 and C8
are LOW, with low-impedance with referenced to CGND.
The DC-to-DC converter is stopped.
When everything is in normal conditions (no error flag set),
the microcontroller will initiate an activation sequence of
the card.
After leaving the UART reset mode and then configuring
the necessary parameters for the UART, the START bit in
thePCR(t
0
)willbeactivated.Thefollowingsequencethen
occurs:
1.
The DC-to-DC converter is started (t
1
)
2.
V
CC
starts rising from 0 to 5 V or 3 or 1.8 V with a
controlled rise time of 0.17 V/
μ
s typically (t
2
)
3.
I/O, C4 and C8 rise to V
CC
(t
3
); integrated 10 k
pull-up resistors connected to V
CC
4.
Clock pulses are sent to the card and RST is enabled
(t
4
).
Afteranumberofclockpulsesthatcanbecountedwiththe
Time-Out Counter, the bit RSTIN may be set by software
and RST will rise to V
CC
.
The sequencer is clocked by
1
64
f
int
which leads to a time
interval of t = 25
μ
s typical.
Thus t
1
= 0 to
3
64
t, t
2
= t
1
+
5
2
t, t
3
= t
1
+
9
2
t
and t
4
= t
1
+ 5t.
相關PDF資料
PDF描述
TDA8030HL USB smart card reader (OTP or ROM)
TDA8031 USB smart card reader (OTP or ROM)
TDA8031HL USB smart card reader (OTP or ROM)
TDA8302 SMALL SIGNAL COMBINATION IC FOR COLOUR TV
TDA8931 Power comparator 1 X 20 W
相關代理商/技術參數
參數描述
TDA8030HL 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:USB smart card reader (OTP or ROM)
TDA8031 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:USB smart card reader (OTP or ROM)
TDA8031HL 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:USB smart card reader (OTP or ROM)
TDA8034AT 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Smart card interface
TDA8034AT/C1 制造商:NXP Semiconductors 功能描述:Cut Tape
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*