- 您現在的位置：買賣IC網 > PDF目錄98145 > ST72E85A5G0 (STMICROELECTRONICS) 8-BIT, UVPROM, 4.332 MHz, MICROCONTROLLER, CQFP80 PDF資料下載
參數資料
| 型號： | ST72E85A5G0 |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, UVPROM, 4.332 MHz, MICROCONTROLLER, CQFP80 |
| 封裝： | WINDOWED, CERAMIC, QFP- 80 |
| 文件頁數： | 79/117頁 |
| 文件大?。?/td> | 748K |
| 代理商： | ST72E85A5G0 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁當前第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁
64/117
ST7285C
4.6 A/D CONVERTER (ADC)
4.6.1 Introduction
The on-chip Analog to Digital Converter peripheral
is a single 8-bit successive approximation ratio-
metric monotonic ADC, to which up to 8 different
analog voltages (depending on device specifica-
tion as illustrated in Block Diagram) may be ap-
plied from external sources. The result of the con-
version is stored in the 8-bit Data Register. The A/
D converter is controlled through the ADC Control/
Status Register.
4.6.2 Functional Description
The A/D converter is enabled by setting the A/D
Converter ON bit (ADON) in the ADC Control/Sta-
tus Register. A delay time is then required for the
converter to stabilize (typically 10
s, see Electrical
Characteristics)).
When the A/D function is enabled, the associated
pins (see MCU Block Diagram) may be used as
analog inputs. The inputs must first be enabled for
analog input by setting the corresponding bit(s) of
the relevant Port Configuration Register as de-
scribed in the Section on I/O Ports. Bits CH2 to
CH0 of the A/D Converter Control/Status Register
may then be coded to select the channel to be
converted. Using a pin, or pins, as analog inputs
does not affect the ability to read the port as logic
inputs.
The A/D converter may be disabled by resetting
the ADON bit. This feature allows the reduction of
power consumption when no conversion is in
progress. The A/D converter is disabled after Pow-
er-On and external resets.
When enabled, the A/D converter performs a con-
tinuous conversion of the selected channel. When
a conversion is completed (16
s for f
CPU =4
MHz), the result is loaded into the read only Result
Data Register and the COCO (Conversion Com-
plete) flag is set. No interrupt is generated. Any
write to the A/D Converter Control/Status Register
aborts the current conversion, resets the COCO
flag and starts a new conversion.
The A/D converter is ratiometric. An input voltage
equal to, or greater than VDD , converts to FFh (full
scale) without overflow indication if greater. An in-
put voltage equal to, or lower than VSS converts to
00h. The conversion is monotonic: the results nev-
er decrease if the analog input does not and never
increase if the analog input does not.
The 8-bit conversion is accurate to within 2 LSB.
The minimal conversion time is 32 ADC clock cy-
cles (16
s if A/D clock frequency at 2 MHz). The
A/D converter clock is generated from the CPU
clock divided by 2.
The high and low level reference voltages are con-
nected to VDD and VSS. Conversion accuracy may
therefore be degraded by voltage drops and noise
in the event of heavily loaded or badly decoupled
power supply lines.
The A/D converter is not affected by WAIT mode
but, in power sensitive applications, it can be disa-
bled before entering this mode. When the MCU
enters HALT mode with the A/D converter ena-
bled, the A/D clocks are stopped and the converter
is disabled until the HALT mode is exited and the
start-up delay has elapsed. A stabilisation time is
also required before accurate conversions can be
performed.
相關PDF資料 |
PDF描述 |
|---|---|
| ST72F321J9T7 | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP44 |
| ST72F321J7T3 | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP44 |
| ST72F321J7T1 | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP44 |
| ST72F321J9T5 | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP44 |
| ST72F324BJ6B6 | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDIP42 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST72F260G1B5 | 功能描述:8位微控制器 -MCU Flask 4K SPI RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| ST72F260G1M6 | 功能描述:8位微控制器 -MCU Flash 4K SPI/I2C/SCI RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| ST72F260G1M6/TR | 功能描述:8位微控制器 -MCU 8B MCU FLASH OR ROM MEMORY RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| ST72F262G1B5 | 功能描述:8位微控制器 -MCU Flask 4K SPI RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| ST72F262G1B6 | 功能描述:8位微控制器 -MCU 8B MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。