- 您現在的位置：買賣IC網 > PDF目錄98145 > ST72E85A5G0 (STMICROELECTRONICS) 8-BIT, UVPROM, 4.332 MHz, MICROCONTROLLER, CQFP80 PDF資料下載
參數資料
| 型號： | ST72E85A5G0 |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, UVPROM, 4.332 MHz, MICROCONTROLLER, CQFP80 |
| 封裝： | WINDOWED, CERAMIC, QFP- 80 |
| 文件頁數： | 53/117頁 |
| 文件大?。?/td> | 748K |
| 代理商： | ST72E85A5G0 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁當前第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁
40/117
ST7285C
16-BIT TIMER (Cont’d)
4.3.5 Output Compare
Two output compare registers are present: Output
Compare Register 1 and Output Compare Regis-
ter 2 (OCR1 and OCR2). These registers can be
used for several purposes, such as controlling an
output waveform or indicating when a period of
time has elapsed. The OCMP
i pin is associated
with the Output Compare
i function (i = 1 or 2).
The Output Compare Registers are unique in that
all bits are readable and writable and are not af-
fected by the timer hardware or by Reset. If a com-
pare function is not used, the two bytes of the cor-
responding Output Compare Registers can be
used as general purpose storage locations.
4.3.5.1 Output Compare Registers
The Output Compare Register
i (OCRi) is a 16-bit
register, which is made up of two 8-bit registers:
the most significant byte register (OCHR
i) and the
least significant byte register (OCLR
i).
In this section, the index,
i, may be 1 or 2.
The content of OCR
i is compared with the content
of the free running counter once during every timer
clock cycles, i.e. once every 8, 4 or 2 internal proc-
essor clock periods or 2 external clock periods ac-
cording to the clock control bits of the Timer Con-
trol Register (TCR2). If match is found, the Output
Compare Flag OCF
i of the TSR is set and the Out-
put Level bit (OLVL
i) of the TCR1 is clocked to the
OCMP
i pin (see output compare timing diagrams
Figure 6, Figure 7, Figure 8). OLVL
i is copied to
the corresponding output level latch and hence, to
the OCMP
i pin regardless of whether the Output
Compare Flag (OCF
i) is set or not. The value in
the OCR
i and the OLVLi bit should be changed af-
ter each successful comparison in order to control
an output waveform or establish a new elapsed
timeout.
An interrupt accompanies a successful output
compare if the corresponding interrupt enable bit
OCIE of the TCR1 is set, provided the I-bit of the
CCR is cleared. Otherwise, the interrupt remains
pending until both conditions are true. It is cleared
by a read of TSR followed by an access to the LSB
of the OCR
i.
After a processor write cycle to the OCHR
i regis-
ter, the output compare function is inhibited until
the OCLR
i is also written. Thus, the user must
write both bytes if the MSB is written first. A write
made to only the LSB will not inhibit the compare
function. The minimum time between two succes-
sive edges on the OCMP
i pin is a function of the
software program and the clock control bits of the
TCR2.
The OCMP
i output latch is forced low during reset
and stays low until valid compares change it to a
high level. Because the OCF
i flag and the OCRi
are undeterminate at power-on and are not affect-
ed by an external reset, care must be exercise
when initiating the output compare function with
software. The following procedure is recommend-
ed to prevent the OCF
i flag from being set be-
tween the time it is read and the write to OCR
i:
– Write to OCHR
i (further compares are inhibited).
– Read the TSR (first step of the clearance of OC-
F
i, which may be already set).
– Write to OCLR
i (enables the output compare
function and clears OCF
i).
相關PDF資料 |
PDF描述 |
|---|---|
| ST72F321J9T7 | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP44 |
| ST72F321J7T3 | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP44 |
| ST72F321J7T1 | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP44 |
| ST72F321J9T5 | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP44 |
| ST72F324BJ6B6 | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDIP42 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST72F260G1B5 | 功能描述:8位微控制器 -MCU Flask 4K SPI RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| ST72F260G1M6 | 功能描述:8位微控制器 -MCU Flash 4K SPI/I2C/SCI RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| ST72F260G1M6/TR | 功能描述:8位微控制器 -MCU 8B MCU FLASH OR ROM MEMORY RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| ST72F262G1B5 | 功能描述:8位微控制器 -MCU Flask 4K SPI RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| ST72F262G1B6 | 功能描述:8位微控制器 -MCU 8B MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。