- 您現在的位置：買賣IC網 > PDF目錄98145 > ST72E85A5G0 (STMICROELECTRONICS) 8-BIT, UVPROM, 4.332 MHz, MICROCONTROLLER, CQFP80 PDF資料下載
參數資料
| 型號： | ST72E85A5G0 |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, UVPROM, 4.332 MHz, MICROCONTROLLER, CQFP80 |
| 封裝： | WINDOWED, CERAMIC, QFP- 80 |
| 文件頁數： | 77/117頁 |
| 文件大?。?/td> | 748K |
| 代理商： | ST72E85A5G0 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁當前第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁
62/117
ST7285C
I
2C BUS INTERFACE (Cont’d)
4.5.6.3 Slave Sending
The Slave waits for the microcontroller to write in
the Data Register. Then it receives data in the
Shift Register and sends it on the SDA line. When
the acknowledge bit is received, the BTF flag is set
and an interrupt is generated if ITE is set.
- Detection of a Stop or Start condition during a
byte transfer: the state machine is reset, the BERR
flag is set and an interrupt is generated.
- Detection of a Start condition after an acknowl-
edge time-slot: the state machine is reset and it
starts a new process. So, the flag ADSL is set and
an interrupt is generated if ITE is set.
- Detection of a Stop condition after an acknowl-
edge time-slot: the state machine is reset. Then
the flag SSTOP is set and an interrupt is generat-
ed if ITE is set.
4.5.6.4 Master mode
The interface operates in Master mode after gen-
erating a Start condition. So, the Start flag must be
set in the control register and the I2C bus must be
free (Busy bit at logic low level).
Once the Start condition is generated, the M/SL
and SB flags are set and an interrupt is generated
if ITE is set. The interface waits for the microcon-
troller to write the Slave address in the Data Reg-
ister by holding the SCL line low.
The address byte is then sent on the SDA line, an
acknowledge clock pulse is sent on the SCL line
and an interrupt is generated if ITE is set. The in-
terface waits for the MCU to write to the Control
Register by holding the SCL line low. If there is no
acknowledge, the AF flag is set and the Master
must write a Start or a Stop in the Control Register.
The state machine then enters a send or a receive
process, depending on the state of the Data Direc-
tion bit (least significant bit); an interrupt is gener-
ated if ITE is set.
If the Master loses control of bus arbitration, there
will be no acknowledge. The AF flag is set and the
Master must write a Start or a Stop in the control
register; the ARLO flag is set, the M/SL flag is
cleared and the process is reset. An interrupt is
generated if ITE is set.
4.5.6.5 Master Sending
The Master waits for the MCU to write in the Data
Register by holding the SCL line low. Then the
byte is received in the shift register and is sent on
the SDA line. The BTF flag is set and an interrupt
is generated if ITE is set.
- Detection of a Stop or of a Start condition during
a byte transfer: the BERR flag is set and an inter-
rupt is generated if ITE is set.
- The Stop bit is set in the Control Register: a Stop
condition is generated after the transfer of the cur-
rent byte, the M/SL flag is cleared and the state
machine is reset. Then an interrupt is generated if
ITE is set.
- The Start bit is set in the Control Register: the
state machine is reset and it starts a new process.
The SB flag is set and an interrupt is generated if
ITE is set.
- There is no acknowledge: the AF flag is set and
an interrupt is generated if ITE is set.
4.5.6.6 Master Receiving
The Master receives a byte from the SDA line into
the shift register and it sends it to the Data Regis-
ter. So, it generates an acknowledge bit if the ACK
bit is set and it generates an interrupt if ITE is set.
Then it waits for the microcontroller to read the
Data Register by holding SCL line low.
- A detection of a Stop or a Start condition during a
byte reception: the flag BERR is set and an inter-
rupt is generated if ITE is set.
- The Stop bit is set in the Control Register: a Stop
condition is generated after the transfer of the cur-
rent byte, the M/SL flag is cleared and the state
machine is reset. Then an interrupt is generated if
ITE is set.
- The Start bit is set in the Control Register: the
state machine is reset and starts a new process.
So, the flag SB is set and an interrupt is generated
if ITE is set.
相關PDF資料 |
PDF描述 |
|---|---|
| ST72F321J9T7 | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP44 |
| ST72F321J7T3 | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP44 |
| ST72F321J7T1 | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP44 |
| ST72F321J9T5 | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP44 |
| ST72F324BJ6B6 | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDIP42 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST72F260G1B5 | 功能描述:8位微控制器 -MCU Flask 4K SPI RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| ST72F260G1M6 | 功能描述:8位微控制器 -MCU Flash 4K SPI/I2C/SCI RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| ST72F260G1M6/TR | 功能描述:8位微控制器 -MCU 8B MCU FLASH OR ROM MEMORY RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| ST72F262G1B5 | 功能描述:8位微控制器 -MCU Flask 4K SPI RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| ST72F262G1B6 | 功能描述:8位微控制器 -MCU 8B MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。