參數資料
型號： SI5315A-C-GMR
廠商： Silicon Laboratories Inc
文件頁數： 22/54頁
文件大?。?/td> 0K
描述： IC CLK MULT 8KHZ-644.53MHZ 36QFN
應用說明： SI5315/17 Crystal Selection AppNote
標準包裝： 250
系列： DSPLL®
類型： 時鐘/頻率倍增器，抖動衰減器，多路復用器
PLL： 無
主要目的： 以太網，SONET/SDH/PDH，電信
輸入： CML，CMOS，LVDS，LVPECL
輸出： CML，CMOS，LVDS，LVPECL
電路數： 1
比率 - 輸入:輸出： 2:2
差分 - 輸入:輸出： 是/是
頻率 - 最大： 644.53MHz
電源電壓： 1.71 V ~ 3.63 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 36-VFQFN 裸露焊盤
供應商設備封裝： 36-QFN（6x6）
包裝： 帶卷 (TR)
Si5315
Rev. 1.0
29
5.2. PLL Self-Calibration
An internal self-calibration (ICAL) is performed before operation to optimize loop parameters and jitter
performance. While the self-calibration is being performed, the DSPLL is being internally controlled by the self-
calibration state machine. The LOL alarm will be active during ICAL. The self-calibration time tLOCKHW is given in
Any of the following events will trigger a self-calibration:
Power-on-reset (POR)
Release of the external reset pin RST (transition of RST from 0 to 1)
Change in FRQSEL, FRQTBL, BWSEL, or XTAL/CLOCK pins
Internal DSPLL registers out-of-range, indicating the need to relock the DSPLL
In any of the above cases, an internal self-calibration will be initiated if a valid input clock exists (no input alarm)
and is selected as the active clock at that time. The external crystal or reference clock must also be present for the
self-calibration to begin. If valid clocks are not present, the self-calibration state machine will wait until they appear,
at which time the calibration will start. An output clock will be active while waiting for a valid input clock. The output
clock frequency is based on the VCO range determine by FRQSEL and FRQTBL settings. This output clock will
vary by ±20%. If no output clock is desired prior to an ICAL, then the SFOUT pins should be kept at LM for
1.2 seconds until the output clock is stable.
After a successful self-calibration has been performed with a valid input clock, no subsequent self calibrations are
performed unless one of the above conditions are met. If the input clock is lost following self-calibration, the device
enters holdover mode. When the input clock returns, the device relocks to the input clock without performing a self-
calibration.
5.2.1. Input Clock Stability during Internal Self-Calibration
An exit from reset must occur when the selected CKINn clock is stable in frequency with a frequency value that is
within the device operating range. The other CKINs must also either be stable in frequency or squelched during a
reset.
5.2.2. Self-Calibration caused by Changes in Input Frequency
If the selected CKINn varies by 500 ppm or more in frequency since the last calibration, the device may initiate a
self-calibration.
5.2.3. Device Reset
Upon powerup, the device internally executes a power-on-reset (POR) which resets the internal device logic. The
pin RST can also be used to initiate a reset. The device stays in this state until a valid CKINn is present, when it
then performs a PLL Self-Calibration (See 5.2. "PLL Self-Calibration”).
5.2.4. Recommended Reset Guidelines
Follow the recommended RESET guidelines in Table 10 when reset should be applied to a device.
Table 10. Si5315 Pins and Reset
Pin #
Si5315 Pin Name
Must Reset after Changing
2FRQTBL
Yes
11
XTAL/CLOCK
Yes
22
BWSEL0
Yes
23
BWSEL1
Yes
24
FRQSEL0
Yes
25
FRQSEL1
Yes
26
FRQSEL2
Yes
27
FRQSEL3
Yes
相關PDF資料
PDF描述
VE-2NT-MY-S CONVERTER MOD DC/DC 6.5V 50W
VE-B3W-IU CONVERTER MOD DC/DC 5.5V 200W
VE-B3T-IU CONVERTER MOD DC/DC 6.5V 200W
VE-2NR-MY-S CONVERTER MOD DC/DC 7.5V 50W
VE-B3P-IU CONVERTER MOD DC/DC 13.8V 200W
相關代理商/技術參數
參數描述
Si5315B-C-GM 功能描述:時鐘發生器及支持產品 Pin-Prgrmmbl SyncE Clck Mlt/Jttr Attntr RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56
SI5315B-C-GMR 功能描述:時鐘發生器及支持產品 Pin-Ctrl SyncE Clk Xplier/Jitt Attn 2/2 RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56
SI5315-C 制造商:AUK 制造商全稱:AUK corp 功能描述:IRED
SI5315-C(B) 制造商:AUK 制造商全稱:AUK corp 功能描述:IRED
SI5315-C_1 制造商:AUK 制造商全稱:AUK corp 功能描述:IRED
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*