- 您現在的位置：買賣IC網 > Datasheet目錄57 > SI4711-B30-GM (Silicon Laboratories Inc)IC TX FM RADIO 76-108MHZ 20UQFN Datasheet資料下載
參數資料
| 型號： | SI4711-B30-GM |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 26/40頁 |
| 文件大?。?/td> | 380K |
| 描述： | IC TX FM RADIO 76-108MHZ 20UQFN |
| 標準包裝： | 490 |
| 頻率： | 76MHz ~ 108MHz |
| 應用： | 通用 |
| 調制或協議： | FM |
| 電流 - 傳輸： | 18.8mA |
| 數據接口： | PCB，表面貼裝 |
| 天線連接器： | PCB，表面貼裝 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 封裝/外殼： | 20-UFQFN 裸露焊盤 |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
Si4710/11-B30
26
Rev. 1.1
After the rising edge of RST
, the pins, GPO1 and
GPO2/INT
, are used as general-purpose output (O) pins
as described in Section 5.12. GPO Outputs . In any
bus mode, commands may only be sent after V
IO
and
V
DD
supplies are applied.
5.11.1. 2-Wire Control Interface Mode
When selecting 2-wire mode, the user must ensure that
SCLK is high during the rising edge of RST
, and stays
high until after the first start condition. Also, a start
condition must not occur within 300 ns before the rising
edge of RST
.
2-wire bus mode uses only the SCLK and SDIO pins for
signaling. A transaction begins with the START
condition, which occurs when SDIO falls while SCLK is
high. Next, the user drives an 8-bit control word serially
on SDIO, which is captured by the device on rising
edges of SCLK. The control word consists of a seven bit
device address followed by a read/write bit (read = 1,
write = 0). The Si4710/11 acknowledges the control
word by driving SDIO low on the next falling edge of
SCLK.
Although the Si4710/11 responds to only a single device
address, this address can be changed with the SEN
pin
(note that the SEN
pin is not used for signaling in 2-wire
mode). When SEN
= 0, the seven-bit device address is
0010001. When SEN
= 1, the address is 1100011.
For write operations, the user then sends an eight bit
data byte on SDIO, which is captured by the device on
rising edges of SCLK. The Si4710/11 acknowledges
each data byte by driving SDIO low for one cycle, on the
next falling edge of SCLK. The user may write up to
eight data bytes in a single two-wire transaction. The
first byte is a command, and the next seven bytes are
arguments.
For read operations, after the Si4710/11 has
acknowledged the control byte, it drives an eight-bit
data byte on SDIO, changing the state of SDIO on the
falling edge of SCLK. The user acknowledges each data
byte by driving SDIO low for one cycle, on the next
falling edge of SCLK. If a data byte is not
acknowledged, the transaction ends. The user may
read up to 16 data bytes in a single two-wire
transaction. These bytes contain the response data
from the Si4710/11.
A 2-wire transaction ends with the STOP condition,
which occurs when SDIO rises while SCLK is high.
For details on timing specifications and diagrams, refer
to
Table 5,
2-Wire
Control
Interface
Characteristics
1,2,3
, on page 7, Figure 2, 2-Wire
Control Interface Read and Write Timing Parameters,
on page 8, and Figure 3, 2-Wire Control Interface Read
and Write Timing Diagram, on page 8.
5.11.2. SPI Control Interface Mode
When selecting SPI mode, the user must ensure that a
rising edge of SCLK does not occur within 300 ns
before the rising edge of RST
.
SPI bus mode uses the SCLK, SDIO, and SEN
pins for
read/write operations. For reads, the user can choose to
receive data from the device on either SDIO or GPO1. A
transaction begins when the user drives SEN
low. The
user then pulses SCLK eight times while driving an 8-bit
control byte (MSB first) serially on SDIO. The device
captures the data on rising edges of SCLK. The control
byte must have one of these values:
0x48 = write eight command/argument bytes (user
drives write data on SDIO)
0x80 = read status byte (device drives read data on
SDIO)
0xA0 = read status byte (device drives read data on
GPO1)
0xC0 = read 16 response bytes (device drives read data
on SDIO)
0xE0 = read 16 response bytes (device drives read data
on GPO1)
When writing a command, after the control byte has
been written, the user must drive exactly eight data
bytes (a command byte and seven argument bytes) on
SDIO. The data will be captured by the device on the
rising edges of SCLK. After all eight data bytes have
been written, the user raises SEN
after the last falling
edge of SCLK to end the transaction.
In any bus mode, before sending a command or reading
a response, the user must first read the status byte to
ensure that the device is ready (CTS bit is high). In SPI
mode, this is done by sending control byte 0x80 or
0xA0, followed by reading a single byte on SDIO or
GPO1. The Si4710/11 changes the state of SDIO or
GPO1 after the falling edges of SCLK. Data should be
captured by the user on the rising edges of SCLK. After
the status byte has been read, the user raises SEN
after
the last falling edge of SCLK to end the transaction.
When reading a response, the user must read exactly
16 data bytes after sending the control byte. It is
recommended that the user keep SEN
low until all bytes
Table 15. Bus Mode Select on Rising Edge of
RST
Bus Mode
GPO1
GPO2/INT
2-Wire
1
0
SPI
1
1 (must drive)
3-Wire
0 (must drive)
0
相關PDF資料 |
PDF描述 |
|---|---|
| SI4713-B30-GMR | IC TX FM RADIO RPS/RDS 20UQFN |
| SKY12146-321LF | IC VAR VOLT ATTEN 12QFN |
| SN171GG-NR | SNAP PROTOBOARD W/NO RADIO |
| SWLP.2450.12.4.B.02 | ANTENNA WI-FI WLAN 2.4GHZ |
| TD4A | SENSOR RTD LIQUID TEMP 2TERM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI4711-B30-GMR | 功能描述:射頻發射器 Si4711 Broadcast FM Transmitter RDS/RBDS RoHS:否 制造商:Micrel 類型:ASK Transmitter 封裝 / 箱體:SOT-23-6 工作頻率:300 MHz to 450 MHz 封裝:Reel |
| Si4712-A20-GM | 功能描述:射頻發射器 Broadcast FM Radio Trns-Pwr Scan RoHS:否 制造商:Micrel 類型:ASK Transmitter 封裝 / 箱體:SOT-23-6 工作頻率:300 MHz to 450 MHz 封裝:Reel |
| Si4712-A-EVB | 功能描述:射頻開發工具 Si4712 Eval Board Use Si4713-A-EVB RoHS:否 制造商:Taiyo Yuden 產品:Wireless Modules 類型:Wireless Audio 工具用于評估:WYSAAVDX7 頻率: 工作電源電壓:3.4 V to 5.5 V |
| Si4712-B30-GM | 功能描述:射頻發射器 FMRadio Trnsmttr w/Rcv PwrScn 3x3x.55 RoHS:否 制造商:Micrel 類型:ASK Transmitter 封裝 / 箱體:SOT-23-6 工作頻率:300 MHz to 450 MHz 封裝:Reel |
| SI4712-B30-GMR | 功能描述:射頻發射器 Si4712 Broadcast FM Transmitt Recvr Scan RoHS:否 制造商:Micrel 類型:ASK Transmitter 封裝 / 箱體:SOT-23-6 工作頻率:300 MHz to 450 MHz 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。