- 您現在的位置：買賣IC網 > Datasheet目錄57 > SI4711-B30-GM (Silicon Laboratories Inc)IC TX FM RADIO 76-108MHZ 20UQFN Datasheet資料下載
參數資料
| 型號： | SI4711-B30-GM |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 23/40頁 |
| 文件大?。?/td> | 380K |
| 描述： | IC TX FM RADIO 76-108MHZ 20UQFN |
| 標準包裝： | 490 |
| 頻率： | 76MHz ~ 108MHz |
| 應用： | 通用 |
| 調制或協議： | FM |
| 電流 - 傳輸： | 18.8mA |
| 數據接口： | PCB，表面貼裝 |
| 天線連接器： | PCB，表面貼裝 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 封裝/外殼： | 20-UFQFN 裸露焊盤 |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
Si4710/11-B30
Rev. 1.1
23
5.4. Line Input
The Si4710/11 provides left and right channel line inputs
(LIN and RIN). The inputs are high-impedance and low-
capacitance, suited to receiving line level signals from
external audio baseband processors. Both line inputs
are low-noise inputs with programmable attenuation.
Passive and active anti-aliasing filters are incorporated
to prevent high frequencies from aliasing into the audio
band and degrading performance.
To ensure optimal audio performance, the Si4710/11
has a TX_LINE_INPUT_LEVEL property that allows the
user to specify the peak amplitude of the analog input
(LILEVEL[9:0]) required to reach the maximum
deviation level programmed in the audio deviation
property, TX_AUDIO_DEVIATION. A corresponding line
input attenuation code, LIATTEN[1:0], is also selected
by the expected peak amplitude level. Table 14 shows
the line attenuation codes.
The line attenuation code is chosen by picking the
lowest Peak Input Voltage in Table 14 that is just above
the expected peak input voltage coming from the audio
baseband processor. For example, if the expected peak
input voltage from the audio baseband processor is
400 mV, the user chooses LIATTEN[1:0] = 10 since the
Peak Input Voltage of 416 mV associated with
LIATTEN[1:0] = 10 is just greater than the expected
peak input voltage of 400 mV. The user also enters
400 mV into the LILEVEL[9:0] to associate this input
level to the maximum frequency deviation level
programmed into the audio deviation property. Note that
selecting a particular value of LIATTEN[1:0] changes
the input resistance of the LIN and RIN pins. This
feature is used for cases where the expected peak input
level exceeds the maximum input level of the LIN and
RIN pins.
The maximum analog input level is 636 mVpK. If the
analog input level from the audio baseband processor
exceeds this voltage, series resistors must be inserted
in front of the LIN and RIN pins to attenuate the voltage
such that it is within the allowable operating range. For
example, if the audio baseband's expected peak
amplitude is 900 mV and the V
IO
supply voltage is 1.8 V,
the designer can use 30 kW series resistors in front of
the LIN and RIN pins and select LIATTEN[1:0] = 11. The
resulting expected peak input voltage at the LIN/RIN
pins is 600 mV, since this is just a voltage divider
between the LIN/RIN input resistance (see Table 14,
60 kW for this example) and the external resistor. Note
that the Peak Input Voltage corresponding to the chosen
LIATTEN[1:0] code still needs to satisfy the condition of
being just greater than the attenuated voltage. In this
example, a line attenuation code of LIATTEN[1:0] = 11
has a Peak Input Voltage of 636 mV, which is just
greater than the expected peak attenuated voltage of
600 mV. Also, the expected peak attenuated voltage is
entered into the LILEVEL[9:0] parameter. Again, in this
example, 600 mV is entered into LILVEVEL[9:0]. This
example shows one possible solution, but many other
solutions exist. The optimal solution is to apply the
largest possible voltage to the LIN and RIN pins for
signal-to-noise considerations; however, practical
resistor values may limit the choices.
Note that the TX_LINE_INPUT_LEVEL parameter will
affect the high-pass filter characteristics of the ac-
coupling capacitors and the resistance of the audio
inputs.
The Si4710/11 has a programmable low audio level and
high audio level indicators that allows the user to
selectively enable and disable the carrier based on the
presence of audio content. The TX_ASQ_LEVEL_LOW
and TX_ASQ_LEVEL_HIGH parameters set the low
level and high level thresholds in dBFS, respectively.
The time required for the audio level to be below the low
threshold is set with the TX_ASQ_DURATION_LOW
parameter, and similarly, the time required for the audio
level to be above the high threshold is set with the
TX_ASQ_DURATION_HIGH parameter.
Table 14. Line Attenuation Codes
LIATTEN[1:0]
Peak Input
Voltage [mV]
RIN/LIN Input
Resistance [kW]
00
190
396
01
301
100
10
416
74
11
636
60
相關PDF資料 |
PDF描述 |
|---|---|
| SI4713-B30-GMR | IC TX FM RADIO RPS/RDS 20UQFN |
| SKY12146-321LF | IC VAR VOLT ATTEN 12QFN |
| SN171GG-NR | SNAP PROTOBOARD W/NO RADIO |
| SWLP.2450.12.4.B.02 | ANTENNA WI-FI WLAN 2.4GHZ |
| TD4A | SENSOR RTD LIQUID TEMP 2TERM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI4711-B30-GMR | 功能描述:射頻發射器 Si4711 Broadcast FM Transmitter RDS/RBDS RoHS:否 制造商:Micrel 類型:ASK Transmitter 封裝 / 箱體:SOT-23-6 工作頻率:300 MHz to 450 MHz 封裝:Reel |
| Si4712-A20-GM | 功能描述:射頻發射器 Broadcast FM Radio Trns-Pwr Scan RoHS:否 制造商:Micrel 類型:ASK Transmitter 封裝 / 箱體:SOT-23-6 工作頻率:300 MHz to 450 MHz 封裝:Reel |
| Si4712-A-EVB | 功能描述:射頻開發工具 Si4712 Eval Board Use Si4713-A-EVB RoHS:否 制造商:Taiyo Yuden 產品:Wireless Modules 類型:Wireless Audio 工具用于評估:WYSAAVDX7 頻率: 工作電源電壓:3.4 V to 5.5 V |
| Si4712-B30-GM | 功能描述:射頻發射器 FMRadio Trnsmttr w/Rcv PwrScn 3x3x.55 RoHS:否 制造商:Micrel 類型:ASK Transmitter 封裝 / 箱體:SOT-23-6 工作頻率:300 MHz to 450 MHz 封裝:Reel |
| SI4712-B30-GMR | 功能描述:射頻發射器 Si4712 Broadcast FM Transmitt Recvr Scan RoHS:否 制造商:Micrel 類型:ASK Transmitter 封裝 / 箱體:SOT-23-6 工作頻率:300 MHz to 450 MHz 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。