- 您現在的位置：買賣IC網 > PDF目錄16512 > SI3056SSI-EVB (Silicon Laboratories Inc)BOARD EVAL SI3056/SI3018 SSI PDF資料下載
參數資料
| 型號： | SI3056SSI-EVB |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 44/94頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL SI3056/SI3018 SSI |
| 標準包裝： | 1 |
| 主要目的： | 電信，數據采集裝置（DAA） |
| 已用 IC / 零件： | Si3056 |
| 已供物品： | 板，CD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁當前第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁
Si3056
Si3018/19/10
Rev. 1.05
49
Reset settings = 0000_0000
Register 1. Control 1
Bit
D7D6D5D4D3D2D1D0
Name
SR
PWMM[1:0]
PWME
IDL
SB
Type
R/W
Bit
Name
Function
7SR
Software Reset.
0 = Enables the DAA for normal operation.
1 = Sets all registers to their reset value.
Note:
Bit automatically clears after being set.
6
Reserved
Read returns zero.
5:4
PWMM[1:0] Pulse Width Modulation Mode.
Used to select the type of signal output on the call progress AOUT pin.
00 = PWM output is clocked at 16.384 MHz as a delta-sigma data stream. A local density of
1s and 0s tracks the combined transmit and receive signals.
01 = Balanced conventional PWM output signal has high and low portions of the modulated
pulse that are centered on the 16 kHz sample clock.
10 = Conventional PWM output signal returns to logic 0 at regular 32 kHz intervals and rises
at a time in the 32 kHz period proportional to its instantaneous amplitude.
11 = Reserved.
3PWME
Pulse Width Modulation Enable.
Sums the transmit and receive audio paths and presents it as a CMOS digital-level output of
PWM data. Use the circuit in “Figure 18. AOUT PWM Circuit for Call Progress” .
0 = Pulse width modulation signal for AOUT disabled.
1 = Pulse width modulation signal for call progress analog output (AOUT) enabled.
2
Reserved
Read returns zero.
1IDL
Isolation Digital Loopback.
0 = Digital loopback across the isolation barrier is disabled.
1 = Enables digital loopback mode across the isolation barrier. The line-side device must be
enabled and off hook before setting this mode. This data path includes the TX and RX filters.
0SB
Serial Digital Interface Mode.
0 = Operation is in 15-bit mode, and the LSB of the data field indicates that a secondary
frame is required.
1 = The serial port is operating in 16-bit mode and requires a secondary frame sync signal,
FC, to initiate control data reads/writes.
相關PDF資料 |
PDF描述 |
|---|---|
| S1812R-223K | INDUCTOR SHIELDED 22UH SMD |
| ILSB1206ER8R2K | INDUCTOR 8.2UH 10% 1206 |
| GEM36DTKN-S288 | CONN EDGECARD 72POS .156 EXTEND |
| 1-5503995-8 | CA 62.5/125UM ZIP OMCER14 |
| XR19L210IL40-0B-EB | EVAL BOARD FOR XR19L202 40QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI3056-X-FS | 制造商:SILABS 制造商全稱:SILABS 功能描述:GLOBAL SERIAL INTERFACE DIRECT ACCESS ARRANGEMENT |
| SI3060 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:GLOBAL LINE-SIDE DAA FOR EMBEDDED SYSTEM-SIDE MODULE |
| SI3060-X-FS | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:GLOBAL LINE-SIDE DAA FOR EMBEDDED SYSTEM-SIDE MODULE |
| SI3060-X-FSR | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:GLOBAL LINE-SIDE DAA FOR EMBEDDED SYSTEM-SIDE MODULE |
| SI3060-X-FT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:GLOBAL LINE-SIDE DAA FOR EMBEDDED SYSTEM-SIDE MODULE |
發布緊急采購，3分鐘左右您將得到回復。