- 您現在的位置：買賣IC網 > PDF目錄365460 > S71WS512NC0BFWE72 (Spansion Inc.) Stacked Multi-Chip Product (MCP) PDF資料下載
參數資料
| 型號： | S71WS512NC0BFWE72 |
| 廠商： | Spansion Inc. |
| 英文描述： | Stacked Multi-Chip Product (MCP) |
| 中文描述： | 堆疊式多芯片產品（MCP） |
| 文件頁數： | 46/188頁 |
| 文件大小： | 2252K |
| 代理商： | S71WS512NC0BFWE72 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁當前第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁
44
S71WS-Nx0 Based MCPs
S71WS-N_01_A4 September 15, 2005
A d v a n c e I n f o r m a t i o n
The system may also write the Autoselect command sequence when the device is in Program Sus-
pend mode. The device allows reading Autoselect codes in the suspended sectors, since the codes
are not stored in the memory array. When the device exits the Autoselect mode, the device re-
verts to Program Suspend mode, and is ready for another valid operation. See “Autoselect
Command Sequence” for more information.
After the Program Resume command is written, the device reverts to programming. The system
can determine the status of the program operation using the DQ7 or DQ6 status bits, just as in
the standard program operation. See “Write Operation Status” for more information.
The system must write the Program Resume command (address bits are “don't care”) to exit the
Program Suspend mode and continue the programming operation. Further writes of the Program
Resume command are ignored. Another Program Suspend command can be written after the de-
vice has resumed programming.
The following is a C source code example of using the program suspend function. Refer to the
Spansion Low Level Driver User’s Guide
(available on www.amd.com and www.fujitsu.com)
for general information on Spansion Flash memory software development guidelines.
/* Example: Program suspend command */
*( (UINT16 *)base_addr + 0x000 ) = 0x00B0; /* write suspend command */
The following is a C source code example of using the program resume function. Refer to the
Spansion Low Level Driver User’s Guide
(available on www.amd.com and www.fujitsu.com)
for general information on Spansion Flash memory software development guidelines.
/* Example: Program resume command */
*( (UINT16 *)base_addr + 0x000 ) = 0x0030; /* write resume command */
10.5.7
Accelerated Program/ Chip Erase
Accelerated single word programming, write buffer programming, sector erase, and chip erase
operations are enabled through the ACC function. This method is faster than the standard chip
program and erase command sequences.
The accelerated chip program and erase functions must not be used more than 10 times
per sector.
In addition, accelerated chip program and erase should be performed at room tem-
perature (25
°
C
±
10
°
C).
If the system asserts V
HH
on this input, the device automatically enters the aforementioned Un-
lock Bypass mode and uses the higher voltage on the input to reduce the time required for
program and erase operations. The system can then use the Write Buffer Load command se-
quence provided by the Unlock Bypass mode. Note that if a “Write-to-Buffer-Abort Reset” is
required while in Unlock Bypass mode, the full 3-cycle RESET command sequence must be used
to reset the device. Removing V
HH
from the ACC input, upon completion of the embedded pro-
gram or erase operation, returns the device to normal operation.
Sectors must be unlocked prior to raising ACC to V
HH
.
The ACC pin must not be at V
HH
for operations other than accelerated programming and ac-
celerated chip erase, or device damage may result.
Table 10.18 Software Functions and Sample Code
Cycle
Operation
Byte Address
Word Address
Data
1
Write
Bank Address
Bank Address
00B0h
Cycle
Operation
Byte Address
Word Address
Data
1
Write
Bank Address
Bank Address
0030h
相關PDF資料 |
PDF描述 |
|---|---|
| S71WS512NC0BFWE73 | Stacked Multi-Chip Product (MCP) |
| S71WS512NC0BFWY20 | Stacked Multi-Chip Product (MCP) |
| S71WS512NC0BFWY22 | Stacked Multi-Chip Product (MCP) |
| S71WS512NC0BFWY23 | Stacked Multi-Chip Product (MCP) |
| S71WS512NC0BFWY30 | Stacked Multi-Chip Product (MCP) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S71WS512NC0BFWE73 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) |
| S71WS512NC0BFWEJ0 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) |
| S71WS512NC0BFWEJ2 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) |
| S71WS512NC0BFWEJ3 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) |
| S71WS512NC0BFWEK0 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) |
發布緊急采購，3分鐘左右您將得到回復。