- 您現在的位置：買賣IC網 > PDF目錄365460 > S71WS512NC0BFWE72 (Spansion Inc.) Stacked Multi-Chip Product (MCP) PDF資料下載
參數資料
| 型號： | S71WS512NC0BFWE72 |
| 廠商： | Spansion Inc. |
| 英文描述： | Stacked Multi-Chip Product (MCP) |
| 中文描述： | 堆疊式多芯片產品（MCP） |
| 文件頁數： | 45/188頁 |
| 文件大?。?/td> | 2252K |
| 代理商： | S71WS512NC0BFWE72 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁當前第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁
September 15, 2005 S71WS-N_01_A4
S71WS-Nx0 Based MCPs
43
A d v a n c e I n f o r m a t i o n
After the erase operation has been suspended, the bank enters the erase-suspend-read mode.
The system can read data from or program data to any sector not selected for erasure. (The de-
vice “erase suspends” all sectors selected for erasure.) Reading at any address within erase-
suspended sectors produces status information on DQ7-DQ0. The system can use DQ7, or DQ6,
and DQ2 together, to determine if a sector is actively erasing or is erase-suspended. Refer to
Table 10.20
for information on these status bits.
After an erase-suspended program operation is complete, the bank returns to the erase-suspend-
read mode. The system can determine the status of the program operation using the DQ7 or DQ6
status bits, just as in the standard program operation.
In the erase-suspend-read mode, the system can also issue the Autoselect command sequence.
Refer to the “Write Buffer Programming Operation” section and the “Autoselect Command Se-
quence” section for details.
To resume the sector erase operation, the system must write the Erase Resume command. The
bank address of the erase-suspended bank is required when writing this command. Further writes
of the Resume command are ignored. Another Erase Suspend command can be written after the
chip has resumed erasing.
The following is a C source code example of using the erase suspend function. Refer to the
Spansion Low Level Driver User’s Guide
(available on www.amd.com and www.fujitsu.com)
for general information on Spansion Flash memory software development guidelines.
/* Example: Erase suspend command */
*( (UINT16 *)bank_addr + 0x000 ) = 0x00B0; /* write suspend command */
The following is a C source code example of using the erase resume function. Refer to the
Spansion Low Level Driver User’s Guide
(available on www.amd.com and www.fujitsu.com)
for general information on Spansion Flash memory software development guidelines.
/* Example: Erase resume command */
*( (UINT16 *)bank_addr + 0x000 ) = 0x0030; /* write resume command */
/* The flash needs adequate time in the resume state */
10.5.6
Program Suspend/ Program Resume Commands
The Program Suspend command allows the system to interrupt an embedded programming op-
eration or a “Write to Buffer” programming operation so that data can read from any non-
suspended sector. When the Program Suspend command is written during a programming pro-
cess, the device halts the programming operation within t
PSL
(program suspend latency) and
updates the status bits. Addresses are “don't-cares” when writing the Program Suspend
command.
After the programming operation has been suspended, the system can read array data from any
non-suspended sector. The Program Suspend command may also be issued during a program-
ming operation while an erase is suspended. In this case, data may be read from any addresses
not in Erase Suspend or Program Suspend. If a read is needed from the Secured Silicon Sector
area, then user must use the proper command sequences to enter and exit this region.
Table 10.17 Software Functions and Sample Code
Cycle
Operation
Byte Address
Word Address
Data
1
Write
Bank Address
Bank Address
00B0h
Cycle
Operation
Byte Address
Word Address
Data
1
Write
Bank Address
Bank Address
0030h
相關PDF資料 |
PDF描述 |
|---|---|
| S71WS512NC0BFWE73 | Stacked Multi-Chip Product (MCP) |
| S71WS512NC0BFWY20 | Stacked Multi-Chip Product (MCP) |
| S71WS512NC0BFWY22 | Stacked Multi-Chip Product (MCP) |
| S71WS512NC0BFWY23 | Stacked Multi-Chip Product (MCP) |
| S71WS512NC0BFWY30 | Stacked Multi-Chip Product (MCP) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S71WS512NC0BFWE73 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) |
| S71WS512NC0BFWEJ0 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) |
| S71WS512NC0BFWEJ2 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) |
| S71WS512NC0BFWEJ3 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) |
| S71WS512NC0BFWEK0 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) |
發布緊急采購，3分鐘左右您將得到回復。